patch-2.3.48 linux/drivers/usb/ftdi_sio.h

Next file: linux/drivers/usb/graphire.c
Previous file: linux/drivers/usb/evdev.c
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.3.47/linux/drivers/usb/ftdi_sio.h linux/drivers/usb/ftdi_sio.h
@@ -0,0 +1,380 @@
+/* Bill Ryder - bryder@sgi.com - wrote the FTDI_SIO implementation */
+/* The device is based on the FTDI FT8U100AX chip, DB25 on one side, USB on the other */
+/* Thanx to FTDI for so kindly providing details of the protocol required */
+/* http://www.ftdi.co.uk  */
+
+/* The implementation of the device I have is called a USC-1000 */
+/*  which is available from http://www.dse.co.nz - cat no XH4214 */
+/* It looks similar to this: http://www.dansdata.com/usbser.htm but I can't be sure */
+/* There are other USC-1000s which don't look like my device though so beware */
+
+/* Definitions for the FTDI USB Single Port Serial Converter */
+/* known as FTDI_SIO (Serial Input/Output application of the chipset) */
+
+#define FTDI_VID	0x0403	/* Vendor Id */
+#define FTDI_SIO_PID	0x8372	/* Product Id */
+
+/* Vendor Request Interface */
+#define FTDI_SIO_RESET 		0 /* Reset the port */
+#define FTDI_SIO_MODEM_CTRL 	1 /* Set the modem control register */
+#define FTDI_SIO_SET_FLOW_CTRL	2 /* Set flow control register */
+#define FTDI_SIO_SET_BAUD_RATE	3 /* Set baud rate */
+#define FTDI_SIO_SET_DATA	4 /* Set the data characteristics of the port */
+#define FTDI_SIO_GET_MODEM_STATUS	5 /* Retrieve current value of modern status register */
+#define FTDI_SIO_SET_EVENT_CHAR	6 /* Set the event character */
+#define FTDI_SIO_SET_ERROR_CHAR	7 /* Set the error character */
+
+/* Port Identifier Table */
+#define PIT_DEFAULT 		0 /* SIOA */
+#define PIT_SIOA		1 /* SIOA */
+/* The device this is tested with one has one port */
+#define PIT_SIOB		2 /* SIOB */
+#define PIT_PARALLEL		3 /* Parallel */
+
+/* FTDI_SIO_RESET */
+#define FTDI_SIO_RESET_REQUEST FTDI_SIO_RESET
+#define FTDI_SIO_RESET_REQUEST_TYPE 0x40
+#define FTDI_SIO_RESET_SIO 0
+#define FTDI_SIO_RESET_PURGE_RX 1
+#define FTDI_SIO_RESET_PURGE_TX 2
+/* 
+   BmRequestType:  0100 0000B
+   bRequest:       FTDI_SIO_RESET
+   wValue:         Control Value 
+                         0 = Reset SIO
+                         1 = Purge RX buffer
+                         2 = Purge TX buffer
+   wIndex:         Port
+   wLength:        0
+   Data:           None
+
+   */
+
+/* FTDI_SIO_SET_BAUDRATE */
+#define FTDI_SIO_SET_BAUDRATE_REQUEST_TYPE 0x40
+#define FTDI_SIO_SET_BAUDRATE_REQUEST 3
+
+/*
+  BmRequestType:  0100 0000B
+  bRequest:       FTDI_SIO_SET_BAUDRATE
+  wValue:         BaudRate value - see below
+  wIndex:         Port
+  wLength:        0
+  Data:           None
+*/
+
+typedef enum {
+ ftdi_sio_b300 = 0, 
+ ftdi_sio_b600 = 1, 
+ ftdi_sio_b1200 = 2,
+ ftdi_sio_b2400 = 3,
+ ftdi_sio_b4800 = 4,
+ ftdi_sio_b9600 = 5,
+ ftdi_sio_b19200 = 6,
+ ftdi_sio_b38400 = 7,
+ ftdi_sio_b57600 = 8,
+ ftdi_sio_b115200 = 9
+} FTDI_SIO_baudrate_t ;
+
+#define FTDI_SIO_SET_DATA_REQUEST FTDI_SIO_SET_DATA
+#define FTDI_SIO_SET_DATA_REQUEST_TYPE 0x40
+#define FTDI_SIO_SET_DATA_PARITY_NONE (0x0 << 8 )
+#define FTDI_SIO_SET_DATA_PARITY_ODD (0x1 << 8 )
+#define FTDI_SIO_SET_DATA_PARITY_EVEN (0x2 << 8 )
+#define FTDI_SIO_SET_DATA_PARITY_MARK (0x3 << 8 )
+#define FTDI_SIO_SET_DATA_PARITY_SPACE (0x4 << 8 )
+#define FTDI_SIO_SET_DATA_STOP_BITS_1 (0x0 << 11 )
+#define FTDI_SIO_SET_DATA_STOP_BITS_15 (0x1 << 11 )
+#define FTDI_SIO_SET_DATA_STOP_BITS_2 (0x2 << 11 )
+
+/* FTDI_SIO_SET_DATA */
+
+/*    BmRequestType:  0100 0000B */
+/*    bRequest:       FTDI_SIO_SET_DATA */
+/*    wValue:         Data characteristics (see below) */
+/*    wIndex:         Port */
+/*    wLength:        0 */
+/*    Data:           None */
+/* 
+  Data characteristics
+
+B0..7   Number of data bits
+B8..10  Parity
+           0 = None
+           1 = Odd
+           2 = Even
+           3 = Mark
+           4 = Space
+ B11..13 Stop Bits
+           0 = 1
+           1 = 1.5
+           2 = 2
+ B14..15 Reserved
+*/
+
+
+
+/* FTDI_SIO_MODEM_CTRL */
+#define FTDI_SIO_SET_MODEM_CTRL_REQUEST_TYPE 0x40
+#define FTDI_SIO_SET_MODEM_CTRL_REQUEST FTDI_SIO_MODEM_CTRL
+
+/* 
+  BmRequestType:   0100 0000B
+  bRequest:        FTDI_SIO_MODEM_CTRL
+  wValue:          ControlValue (see below)
+  wIndex:          Port
+  wLength:         0
+  Data:            None
+
+  NOTE: If the device is in RTS/CTS flow control, the RTS set by this
+        command will be IGNORED without an error being returned
+*/
+
+#define FTDI_SIO_SET_DTR_MASK 0x1
+#define FTDI_SIO_SET_DTR_HIGH ( 1 | ( FTDI_SIO_SET_DTR_MASK  << 8))
+#define FTDI_SIO_SET_DTR_LOW  ( 0 | ( FTDI_SIO_SET_DTR_MASK  << 8))
+#define FTDI_SIO_SET_RTS_MASK 0x2
+#define FTDI_SIO_SET_RTS_HIGH ( 2 | ( FTDI_SIO_SET_RTS_MASK << 8 ))
+#define FTDI_SIO_SET_RTS_LOW ( 0 | ( FTDI_SIO_SET_RTS_MASK << 8 ))
+
+/* ControlValue
+   B0    DTR state
+           0 = reset
+           1 = set
+   B1    RTS state
+           0 = reset
+           1 = set
+   B2..7 Reserved
+   B8    DTR state enable
+           0 = ignore
+           1 = use DTR state
+   B9    RTS state enable
+           0 = ignore
+           1 = use RTS state
+   B10..15 Reserved
+*/
+
+/* FTDI_SIO_SET_FLOW_CTRL */
+#define FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE 0x40
+#define FTDI_SIO_SET_FLOW_CTRL_REQUEST FTDI_SIO_SET_FLOW_CTRL
+#define FTDI_SIO_DISABLE_FLOW_CTRL 0x0 
+#define FTDI_SIO_RTS_CTS_HS 0x1
+#define FTDI_SIO_DTR_DSR_HS 0x2
+#define FTDI_SIO_XON_XOFF_HS 0x4
+/* 
+   BmRequestType:  0100 0000b
+   bRequest:       FTDI_SIO_SET_FLOW_CTRL
+   wValue:         Xoff/Xon
+   wIndex:         Protocol/Port - hIndex is protocl / lIndex is port
+   wLength:        0 
+   Data:           None
+
+hIndex - protocol has
+ B0 Output handshaking using RTS/CTS
+      0 = disabled
+      1 = enabled
+ B1 Output handshaking using DTR/DSR
+      0 = disabled
+      1 = enabled
+ B2 Xon/Xoff handshaking
+      0 = disabled
+      1 = enabled
+
+A value of zero in the hIndex field selects no handshaking
+
+If Xon/Xoff handshaking is specified, the hValue field contains the Xoff character 
+and the lValue field contains the Xon character.
+
+*/  
+ 
+/* FTDI_SIO_SET_EVENT_CHAR */
+/* Set the special event character for the specified communications port */
+/* If the device sees this character it will immediately return the */
+/* data read so far - rather than wait 40ms or until 62 bytes is read */
+#define  FTDI_SIO_SET_EVENT_CHAR_REQUEST FTDI_SIO_SET_EVENT_CHAR
+#define  FTDI_SIO_SET_EVENT_CHAR_REQUEST_TYPE 0x40
+
+
+/* 
+  BmRequestType:   0100 0000b
+  bRequest:        FTDI_SIO_SET_EVENT_CHAR
+  wValue:          EventChar
+  wIndex:          Port
+  wLength:         0
+  Data:            None
+
+wValue:
+   B0..7   Event Character
+   B8      Event Character Processing
+             0 = disabled
+             1 = enabled
+   B9..15  Reserved
+
+*/
+          
+/* FTDI_SIO_SET_ERROR_CHAR */
+/* Set the parity error replacement character for the specified communications port */
+
+/* 
+  BmRequestType:  0100 0000b
+  bRequest:       FTDI_SIO_SET_EVENT_CHAR
+  wValue:         Error Char
+  wIndex:         Port
+  wLength:        0
+  Data:           None
+
+Error Char
+  B0..7  Error Character
+  B8     Error Character Processing
+           0 = disabled
+           1 = enabled
+  B9..15 Reserved
+
+*/
+
+/* FTDI_SIO_GET_MODEM_STATUS */
+/* Retreive the current value of the modem status register */
+
+#define FTDI_SIO_GET_MODEM_STATUS_REQUEST_TYPE 0xc0
+#define FTDI_SIO_GET_MODEM_STATUS_REQUEST FTDI_SIO_GET_MODEM_STATUS
+#define FTDI_SIO_CTS_MASK 0x10
+#define FTDI_SIO_DSR_MASK 0x20
+#define FTDI_SIO_RI_MASK  0x40
+#define FTDI_SIO_RLSD_MASK 0x80
+/* 
+  BmRequestType:   1100 0000b
+  bRequest:        FTDI_SIO_GET_MODEM_STATUS
+  wValue:          zero
+  wIndex:          Port
+  wLength:         1
+  Data:            Status
+
+One byte of data is returned 
+B0..3 0
+B4    CTS
+        0 = inactive
+        1 = active
+B5    DSR
+        0 = inactive
+        1 = active
+B6    Ring Indicator (RI)
+        0 = inactive
+        1 = active
+B7    Receive Line Signal Detect (RLSD)
+        0 = inactive
+        1 = active 
+*/
+
+
+
+/* Descriptors returned by the device 
+
+ Device Descriptor
+
+Offset	Field		Size	Value	Description
+0	bLength		1	0x12	Size of descriptor in bytes
+1	bDescriptorType	1	0x01	DEVICE Descriptor Type
+2	bcdUSB		2	0x0110	USB Spec Release Number
+4	bDeviceClass	1	0x00	Class Code
+5	bDeviceSubClass	1	0x00	SubClass Code
+6	bDeviceProtocol	1	0x00	Protocol Code
+7	bMaxPacketSize0 1	0x08	Maximum packet size for endpoint 0
+8	idVendor	2	0x0403	Vendor ID
+10	idProduct	2	0x8372	Product ID (FTDI_SIO_PID)
+12	bcdDevice	2	0x0001	Device release number
+14	iManufacturer	1	0x01	Index of man. string desc
+15	iProduct	1	0x02	Index of prod string desc
+16	iSerialNumber	1	0x02	Index of serial nmr string desc
+17	bNumConfigurations 1    0x01	Number of possible configurations
+
+Configuration Descriptor
+
+Offset	Field			Size	Value
+0	bLength			1	0x09	Size of descriptor in bytes
+1	bDescriptorType		1	0x02	CONFIGURATION Descriptor Type
+2	wTotalLength		2	0x0020	Total length of data
+4	bNumInterfaces		1	0x01	Number of interfaces supported
+5	bConfigurationValue	1	0x01	Argument for SetCOnfiguration() req
+6	iConfiguration		1	0x02	Index of config string descriptor
+7	bmAttributes		1	0x20	Config characteristics Remote Wakeup
+8	MaxPower		1	0x1E	Max power consumption
+
+Interface Descriptor
+
+Offset	Field			Size	Value
+0	bLength			1	0x09	Size of descriptor in bytes
+1	bDescriptorType		1	0x04	INTERFACE Descriptor Type
+2	bInterfaceNumber	1	0x00	Number of interface
+3	bAlternateSetting	1	0x00	Value used to select alternate
+4	bNumEndpoints		1	0x02	Number of endpoints
+5	bInterfaceClass		1	0xFF	Class Code
+6	bInterfaceSubClass	1	0xFF	Subclass Code
+7	bInterfaceProtocol	1	0xFF	Protocol Code
+8	iInterface		1	0x02	Index of interface string description
+
+IN Endpoint Descriptor
+
+Offset	Field			Size	Value
+0	bLength			1	0x07	Size of descriptor in bytes
+1	bDescriptorType		1	0x05	ENDPOINT descriptor type
+2	bEndpointAddress	1	0x82	Address of endpoint
+3	bmAttributes		1	0x02	Endpoint attributes - Bulk
+4	bNumEndpoints		2	0x0040	maximum packet size
+5	bInterval		1	0x00	Interval for polling endpoint
+
+OUT Endpoint Descriptor
+
+Offset	Field			Size	Value
+0	bLength			1	0x07	Size of descriptor in bytes
+1	bDescriptorType		1	0x05	ENDPOINT descriptor type
+2	bEndpointAddress	1	0x02	Address of endpoint
+3	bmAttributes		1	0x02	Endpoint attributes - Bulk
+4	bNumEndpoints		2	0x0040	maximum packet size
+5	bInterval		1	0x00	Interval for polling endpoint
+    
+DATA FORMAT
+
+IN Endpoint
+
+The device reserves the first two bytes of data on this endpoint to contain the current
+values of the modem and line status registers. In the absence of data, the device 
+generates a message consisting of these two status bytes every 40 ms
+
+Byte 0: Modem Status
+
+Offset	Description
+B0	Reserved - must be 1
+B1	Reserved - must be 0
+B2	Reserved - must be 0
+B3	Reserved - must be 0
+B4	Clear to Send (CTS)
+B5	Data Set Ready (DSR)
+B6	Ring Indicator (RI)
+B7	Receive Line Signal Detect (RLSD)
+
+Byte 1: Line Status
+
+Offset	Description
+B0	Data Ready (DR)
+B1	Overrun Error (OE)
+B2	Parity Error (PE)
+B3	Framing Error (FE)
+B4	Break Interrupt (BI)
+B5	Transmitter Holding Register (THRE)
+B6	Transmitter Empty (TEMT)
+B7	Error in RCVR FIFO
+
+OUT Endpoint
+
+This device reserves the first bytes of data on this endpoint contain the length
+and port identifier of the message. For the FTDI USB Serial converter the port 
+identifier is always 1.
+
+Byte 0: Line Status
+
+Offset	Description
+B0	Reserved - must be 1
+B1	Reserved - must be 0
+B2..7	Length of message - (not including Byte 0)
+
+*/

FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)