patch-2.3.51 linux/drivers/sound/lowlevel/aedsp16.c

Next file: linux/drivers/sound/lowlevel/awe_compat.h
Previous file: linux/drivers/sound/lowlevel/aci.c
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.3.50/linux/drivers/sound/lowlevel/aedsp16.c linux/drivers/sound/lowlevel/aedsp16.c
@@ -1,1400 +0,0 @@
-/*
-   drivers/sound/lowlevel/aedsp16.c
-
-   Audio Excel DSP 16 software configuration routines
-   Copyright (C) 1995,1996,1997,1998  Riccardo Facchetti (fizban@tin.it)
-
-   This program is free software; you can redistribute it and/or modify
-   it under the terms of the GNU General Public License as published by
-   the Free Software Foundation; either version 2 of the License, or
-   (at your option) any later version.
-
-   This program is distributed in the hope that it will be useful,
-   but WITHOUT ANY WARRANTY; without even the implied warranty of
-   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-   GNU General Public License for more details.
-
-   You should have received a copy of the GNU General Public License
-   along with this program; if not, write to the Free Software
-   Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
-
- */
-/*
- * Include the main OSS Lite header file. It include all the os, OSS Lite, etc
- * headers needed by this source.
- */
-#include <linux/config.h>
-#include <linux/delay.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include "../sound_config.h"
-#include "../soundmodule.h"
-
-/*
- * Sanity checks
- */
-
-#if !defined(CONFIG_AEDSP16_BASE)
-# undef CONFIG_AEDSP16
-#else
-# if defined(MODULE) && defined(CONFIG_AEDSP16_MODULE)
-#  define CONFIG_AEDSP16 1
-# endif
-#endif
-
-
-#if defined(CONFIG_AEDSP16)
-
-#if defined(CONFIG_AEDSP16_SBPRO) && defined(CONFIG_AEDSP16_MSS)
-#error You have to enable only one of the MSS and SBPRO emulations.
-#endif
-
-/*
-
-   READ THIS
-
-   This module started to configure the Audio Excel DSP 16 Sound Card.
-   Now works with the SC-6000 (old aedsp16) and new SC-6600 based cards.
-
-   NOTE: I have NO idea about Audio Excel DSP 16 III. If someone owns this
-   audio card and want to see the kernel support for it, please contact me.
-
-   Audio Excel DSP 16 is an SB pro II, Microsoft Sound System and MPU-401
-   compatible card.
-   It is software-only configurable (no jumpers to hard-set irq/dma/mpu-irq),
-   so before this module, the only way to configure the DSP under linux was
-   boot the MS-DOS loading the sound.sys device driver (this driver soft-
-   configure the sound board hardware by massaging someone of its registers),
-   and then ctrl-alt-del to boot linux with the DSP configured by the DOS
-   driver.
-
-   This module works configuring your Audio Excel DSP 16's irq, dma and
-   mpu-401-irq. The OSS Lite routines rely on the fact that if the
-   hardware is there, they can detect it. The problem with AEDSP16 is
-   that no hardware can be found by the probe routines if the sound card
-   is not configured properly. Sometimes the kernel probe routines can find
-   an SBPRO even when the card is not configured (this is the standard setup
-   of the card), but the SBPRO emulation don't work well if the card is not
-   properly initialized. For this reason
-
-   aedsp16_init_board()
-
-   routine is called before the OSS Lite probe routines try to detect the
-   hardware.
-
-   NOTE (READ THE NOTE TOO, IT CONTAIN USEFUL INFORMATIONS)
-
-   NOTE: Now it works with SC-6000 and SC-6600 based audio cards. The new cards
-   have no jumper switch at all. No more WSS or MPU-401 I/O port switches. They
-   have to be configured by software.
-
-   NOTE: The driver is merged with the new OSS Lite sound driver. It works
-   as a lowlevel driver.
-
-   The Audio Excel DSP 16 Sound Card emulates both SBPRO and MSS;
-   the OSS Lite sound driver can be configured for SBPRO and MSS cards
-   at the same time, but the aedsp16 can't be two cards!!
-   When we configure it, we have to choose the SBPRO or the MSS emulation
-   for AEDSP16. We also can install a *REAL* card of the other type (see [1]).
-
-   NOTE: If someone can test the combination AEDSP16+MSS or AEDSP16+SBPRO
-   please let me know if it works.
-
-   The MPU-401 support can be compiled in together with one of the other
-   two operating modes.
-
-   NOTE: This is something like plug-and-play: we have only to plug
-   the AEDSP16 board in the socket, and then configure and compile
-   a kernel that uses the AEDSP16 software configuration capability.
-   No jumper setting is needed!
-
-   For example, if you want AEDSP16 to be an SBPro, on irq 10, dma 3
-   you have just to make config the OSS Lite package, configuring
-   the AEDSP16 sound card, then activating the SBPro emulation mode
-   and at last configuring IRQ and DMA.
-   Compile the kernel and run it.
-
-   NOTE: This means for SC-6000 cards that you can choose irq and dma,
-   but not the I/O addresses. To change I/O addresses you have to set
-   them with jumpers. For SC-6600 cards you have no jumpers so you have
-   to set up your full card configuration in the make config.
-
-   You can change the irq/dma/mirq settings WITHOUT THE NEED to open
-   your computer and massage the jumpers (there are no irq/dma/mirq
-   jumpers to be configured anyway, only I/O BASE values have to be
-   configured with jumpers)
-
-   For some ununderstandable reason, the card default of irq 7, dma 1,
-   don't work for me. Seems to be an IRQ or DMA conflict. Under heavy
-   HDD work, the kernel start to erupt out a lot of messages like:
-
-   'Sound: DMA timed out - IRQ/DRQ config error?'
-
-   For what I can say, I have NOT any conflict at irq 7 (under linux I'm
-   using the lp polling driver), and dma line 1 is unused as stated by
-   /proc/dma. I can suppose this is a bug of AEDSP16. I know my hardware so
-   I'm pretty sure I have not any conflict, but may be I'm wrong. Who knows!
-   Anyway a setting of irq 10, dma 3 works really fine.
-
-   NOTE: if someone can use AEDSP16 with irq 7, dma 1, please let me know
-   the emulation mode, all the installed hardware and the hardware
-   configuration (irq and dma settings of all the hardware).
-
-   This init module should work with SBPRO+MSS, when one of the two is
-   the AEDSP16 emulation and the other the real card. (see [1])
-   For example:
-
-   AEDSP16 (0x220) in SBPRO emu (0x220) + real MSS + other
-   AEDSP16 (0x220) in MSS emu + real SBPRO (0x240) + other
-
-   MPU401 should work. (see [2])
-
-   [1]
-       ---
-       Date: Mon, 29 Jul 1997 08:35:40 +0100
-       From: Mr S J Greenaway <sjg95@unixfe.rl.ac.uk>
-
-       [...]
-       Just to let you know got my Audio Excel (emulating a MSS) working
-       with my original SB16, thanks for the driver!
-       [...]
-       ---
-
-   [2] Not tested by me for lack of hardware.
-
-   TODO, WISHES AND TECH
-
-   - About I/O ports allocation -
-
-   Request the 2x0h region (port base) in any case if we are using this card.
-
-   NOTE: the "aedsp16 (base)" string with which we are requesting the aedsp16
-   port base region (see code) does not mean necessarily that we are emulating
-   sbpro.  Even if this region is the sbpro I/O ports region, we use this
-   region to access the control registers of the card, and if emulating
-   sbpro, I/O sbpro registers too. If we are emulating MSS, the sbpro
-   registers are not used, in no way, to emulate an sbpro: they are
-   used only for configuration purposes.
-
-   Started Fri Mar 17 16:13:18 MET 1995
-
-   v0.1 (ALPHA, was an user-level program called AudioExcelDSP16.c)
-   - Initial code.
-   v0.2 (ALPHA)
-   - Cleanups.
-   - Integrated with Linux voxware v 2.90-2 kernel sound driver.
-   - SoundBlaster Pro mode configuration.
-   - Microsoft Sound System mode configuration.
-   - MPU-401 mode configuration.
-   v0.3 (ALPHA)
-   - Cleanups.
-   - Rearranged the code to let aedsp16_init_board be more general.
-   - Erased the REALLY_SLOW_IO. We don't need it. Erased the linux/io.h
-   inclusion too. We rely on os.h
-   - Used the  to get a variable
-   len string (we are not sure about the len of Copyright string).
-   This works with any SB and compatible.
-   - Added the code to request_region at device init (should go in
-   the main body of voxware).
-   v0.4 (BETA)
-   - Better configure.c patch for aedsp16 configuration (better
-   logic of inclusion of AEDSP16 support)
-   - Modified the conditional compilation to better support more than
-   one sound card of the emulated type (read the NOTES above)
-   - Moved the sb init routine from the attach to the very first
-   probe in sb_card.c
-   - Rearrangements and cleanups
-   - Wiped out some unnecessary code and variables: this is kernel
-   code so it is better save some TEXT and DATA
-   - Fixed the request_region code. We must allocate the aedsp16 (sbpro)
-   I/O ports in any case because they are used to access the DSP
-   configuration registers and we can not allow anyone to get them.
-   v0.5
-   - cleanups on comments
-   - prep for diffs against v3.0-proto-950402
-   v0.6
-   - removed the request_region()s when compiling the MODULE sound.o
-   because we are not allowed (by the actual voxware structure) to
-   release_region()
-   v0.7 (pre ALPHA, not distributed)
-   - started porting this module to kernel 1.3.84. Dummy probe/attach
-   routines.
-   v0.8 (ALPHA)
-   - attached all the init routines.
-   v0.9 (BETA)
-   - Integrated with linux-pre2.0.7
-   - Integrated with configuration scripts.
-   - Cleaned up and beautyfied the code.
-   v0.9.9 (BETA)
-   - Thanks to Piercarlo Grandi: corrected the conditonal compilation code.
-     Now only the code configured is compiled in, with some memory saving.
-   v0.9.10
-   - Integration into the sound/lowlevel/ section of the sound driver.
-   - Re-organized the code.
-   v0.9.11 (not distributed)
-   - Rewritten the init interface-routines to initialize the AEDSP16 in
-     one shot.
-   - More cosmetics.
-   - SC-6600 support.
-   - More soft/hard configuration.
-   v0.9.12
-   - Refined the v0.9.11 code with conditional compilation to distinguish
-     between SC-6000 and SC-6600 code.
-   v1.0.0
-   - Prep for merging with OSS Lite and Linux kernel 2.1.13
-   - Corrected a bug in request/check/release region calls (thanks to the
-     new kernel exception handling).
-   v1.1
-   - Revamped for integration with new modularized sound drivers: to enhance
-     the flexibility of modular version, I have removed all the conditional
-     compilation for SBPRO, MPU and MSS code. Now it is all managed with
-     the ae_config structure.
-   v1.2
-   - Module informations added.
-   - Removed aedsp16_delay_10msec(), now using mdelay(10)
-   - All data and funcs moved to .*.init section.
-
-   Known Problems:
-   - Audio Excel DSP 16 III don't work with this driver.
-
-   Credits:
-   Many thanks to Gerald Britton <gbritton@CapAccess.org>. He helped me a
-   lot in testing the 0.9.11 and 0.9.12 versions of this driver.
-
- */
-
-
-#define VERSION "1.2"		/* Version of Audio Excel DSP 16 driver */
-
-#undef	AEDSP16_DEBUG 1		/* Define this to enable debug code     */
-#undef	AEDSP16_DEBUG_MORE 1	/* Define this to enable more debug     */
-#undef	AEDSP16_INFO  1		/* Define this to enable info code      */
-
-#if defined(AEDSP16_DEBUG)
-# define DBG(x)  printk x
-# if defined(AEDSP16_DEBUG_MORE)
-#  define DBG1(x) printk x
-# else
-#  define DBG1(x)
-# endif
-#else
-# define DBG(x)
-# define DBG1(x)
-#endif
-
-/*
- * Misc definitions
- */
-#define TRUE	1
-#define FALSE	0
-
-/*
- * Region Size for request/check/release region.
- */
-#define IOBASE_REGION_SIZE	0x10
-
-/*
- * Hardware related defaults
- */
-#define DEF_AEDSP16_IOB 0x220   /* 0x220(default) 0x240                 */
-#define DEF_AEDSP16_IRQ 7	/* 5 7(default) 9 10 11                 */
-#define DEF_AEDSP16_MRQ 0	/* 5 7 9 10 0(default), 0 means disable */
-#define DEF_AEDSP16_DMA 1	/* 0 1(default) 3                       */
-
-/*
- * Commands of AEDSP16's DSP (SBPRO+special).
- * Some of them are COMMAND_xx, in the future they may change.
- */
-#define WRITE_MDIRQ_CFG   0x50	/* Set M&I&DRQ mask (the real config)   */
-#define COMMAND_52        0x52	/*                                      */
-#define READ_HARD_CFG     0x58	/* Read Hardware Config (I/O base etc)  */
-#define COMMAND_5C        0x5c	/*                                      */
-#define COMMAND_60        0x60	/*                                      */
-#define COMMAND_66        0x66	/*                                      */
-#define COMMAND_6C        0x6c	/*                                      */
-#define COMMAND_6E        0x6e	/*                                      */
-#define COMMAND_88        0x88	/*                                      */
-#define DSP_INIT_MSS      0x8c	/* Enable Microsoft Sound System mode   */
-#define COMMAND_C5        0xc5	/*                                      */
-#define GET_DSP_VERSION   0xe1	/* Get DSP Version                      */
-#define GET_DSP_COPYRIGHT 0xe3	/* Get DSP Copyright                    */
-
-/*
- * Offsets of AEDSP16 DSP I/O ports. The offset is added to base I/O port
- * to have the actual I/O port.
- * Register permissions are:
- * (wo) == Write Only
- * (ro) == Read  Only
- * (w-) == Write
- * (r-) == Read
- */
-#define DSP_RESET    0x06	/* offset of DSP RESET             (wo) */
-#define DSP_READ     0x0a	/* offset of DSP READ              (ro) */
-#define DSP_WRITE    0x0c	/* offset of DSP WRITE             (w-) */
-#define DSP_COMMAND  0x0c	/* offset of DSP COMMAND           (w-) */
-#define DSP_STATUS   0x0c	/* offset of DSP STATUS            (r-) */
-#define DSP_DATAVAIL 0x0e	/* offset of DSP DATA AVAILABLE    (ro) */
-
-
-#define RETRY           10	/* Various retry values on I/O opera-   */
-#define STATUSRETRY   1000	/* tions. Sometimes we have to          */
-#define HARDRETRY   500000	/* wait for previous cmd to complete    */
-
-/*
- * Size of character arrays that store name and version of sound card
- */
-#define CARDNAMELEN 15		/* Size of the card's name in chars     */
-#define CARDVERLEN  2		/* Size of the card's version in chars  */
-
-#if defined(CONFIG_SC6600)
-/*
- * Bitmapped flags of hard configuration
- */
-/*
- * Decode macros (xl == low byte, xh = high byte)
- */
-#define IOBASE(xl)		((xl & 0x01)?0x240:0x220)
-#define JOY(xl)  		(xl & 0x02)
-#define MPUADDR(xl)		( 			\
-				(xl & 0x0C)?0x330:	\
-				(xl & 0x08)?0x320:	\
-				(xl & 0x04)?0x310:	\
-						0x300)
-#define WSSADDR(xl)		((xl & 0x10)?0xE80:0x530)
-#define CDROM(xh)		(xh & 0x20)
-#define CDROMADDR(xh)		(((xh & 0x1F) << 4) + 0x200)
-/*
- * Encode macros
- */
-#define BLDIOBASE(xl, val) {		\
-	xl &= ~0x01; 			\
-	if (val == 0x240)		\
-		xl |= 0x01;		\
-	}
-#define BLDJOY(xl, val) {		\
-	xl &= ~0x02; 			\
-	if (val == 1)			\
-		xl |= 0x02;		\
-	}
-#define BLDMPUADDR(xl, val) {		\
-	xl &= ~0x0C;			\
-	switch (val) {			\
-		case 0x330:		\
-			xl |= 0x0C;	\
-			break;		\
-		case 0x320:		\
-			xl |= 0x08;	\
-			break;		\
-		case 0x310:		\
-			xl |= 0x04;	\
-			break;		\
-		case 0x300:		\
-			xl |= 0x00;	\
-			break;		\
-		default:		\
-			xl |= 0x00;	\
-			break;		\
-		}			\
-	}
-#define BLDWSSADDR(xl, val) {		\
-	xl &= ~0x10; 			\
-	if (val == 0xE80)		\
-		xl |= 0x10;		\
-	}
-#define BLDCDROM(xh, val) {		\
-	xh &= ~0x20; 			\
-	if (val == 1)			\
-		xh |= 0x20;		\
-	}
-#define BLDCDROMADDR(xh, val) {		\
-	int tmp = val;			\
-	tmp -= 0x200;			\
-	tmp >>= 4;			\
-	tmp &= 0x1F;			\
-	xh |= tmp;			\
-	xh &= 0x7F;			\
-	xh |= 0x40;			\
-	}
-#endif /* CONFIG_SC6600 */
-
-/*
- * Bit mapped flags for calling aedsp16_init_board(), and saving the current
- * emulation mode.
- */
-#define INIT_NONE   (0   )
-#define INIT_SBPRO  (1<<0)
-#define INIT_MSS    (1<<1)
-#define INIT_MPU401 (1<<2)
-
-static int      soft_cfg __initdata = 0;	/* bitmapped config */
-static int      soft_cfg_mss __initdata = 0;	/* bitmapped mss config */
-static int      ver[CARDVERLEN] __initdata = {0, 0};	/* DSP Ver:
-						   hi->ver[0] lo->ver[1] */
-
-#if defined(CONFIG_SC6600)
-static int	hard_cfg[2]     /* lo<-hard_cfg[0] hi<-hard_cfg[1]      */
-                     __initdata = { 0, 0};
-#endif /* CONFIG_SC6600 */
-
-#if defined(CONFIG_SC6600)
-/* Decoded hard configuration */
-struct	d_hcfg {
-	int iobase;
-	int joystick;
-	int mpubase;
-	int wssbase;
-	int cdrom;
-	int cdrombase;
-};
-
-struct d_hcfg decoded_hcfg __initdata = {0, };
-
-#endif /* CONFIG_SC6600 */
-
-/* orVals contain the values to be or'ed       				*/
-struct orVals {
-	int	val;		/* irq|mirq|dma                         */
-	int	or;		/* soft_cfg |= TheStruct.or             */
-};
-
-/* aedsp16_info contain the audio card configuration                  */
-struct aedsp16_info {
-	int base_io;            /* base I/O address for accessing card  */
-	int irq;                /* irq value for DSP I/O                */
-	int mpu_irq;            /* irq for mpu401 interface I/O         */
-	int dma;                /* dma value for DSP I/O                */
-	int mss_base;           /* base I/O for Microsoft Sound System  */
-	int mpu_base;           /* base I/O for MPU-401 emulation       */
-	int init;               /* Initialization status of the card    */
-};
-
-/*
- * Magic values that the DSP will eat when configuring irq/mirq/dma
- */
-/* DSP IRQ conversion array             */
-static struct orVals orIRQ[] __initdata = {
-	{0x05, 0x28},
-	{0x07, 0x08},
-	{0x09, 0x10},
-	{0x0a, 0x18},
-	{0x0b, 0x20},
-	{0x00, 0x00}
-};
-
-/* MPU-401 IRQ conversion array         */
-static struct orVals orMIRQ[] __initdata = {
-	{0x05, 0x04},
-	{0x07, 0x44},
-	{0x09, 0x84},
-	{0x0a, 0xc4},
-	{0x00, 0x00}
-};
-
-/* DMA Channels conversion array        */
-static struct orVals orDMA[] __initdata = {
-	{0x00, 0x01},
-	{0x01, 0x02},
-	{0x03, 0x03},
-	{0x00, 0x00}
-};
-
-static struct aedsp16_info ae_config __initdata = {
-	DEF_AEDSP16_IOB,
-	DEF_AEDSP16_IRQ,
-	DEF_AEDSP16_MRQ,
-	DEF_AEDSP16_DMA,
-	-1,
-	-1,
-	INIT_NONE
-};
-
-/*
- * Buffers to store audio card informations
- */
-static char     DSPCopyright[CARDNAMELEN + 1] __initdata = {0, };
-static char     DSPVersion[CARDVERLEN + 1] __initdata = {0, };
-
-static int __init aedsp16_wait_data(int port)
-{
-	int             loop = STATUSRETRY;
-	unsigned char   ret = 0;
-
-	DBG1(("aedsp16_wait_data (0x%x): ", port));
-
-	do {
-		  ret = inb(port + DSP_DATAVAIL);
-	/*
-	 * Wait for data available (bit 7 of ret == 1)
-	 */
-	  } while (!(ret & 0x80) && loop--);
-
-	if (ret & 0x80) {
-		DBG1(("success.\n"));
-		return TRUE;
-	}
-
-	DBG1(("failure.\n"));
-	return FALSE;
-}
-
-static int __init aedsp16_read(int port)
-{
-	int inbyte;
-
-	DBG(("    Read DSP Byte (0x%x): ", port));
-
-	if (aedsp16_wait_data(port) == FALSE) {
-		DBG(("failure.\n"));
-		return -1;
-	}
-
-	inbyte = inb(port + DSP_READ);
-
-	DBG(("read [0x%x]/{%c}.\n", inbyte, inbyte));
-
-	return inbyte;
-}
-
-static int __init aedsp16_test_dsp(int port)
-{
-	return ((aedsp16_read(port) == 0xaa) ? TRUE : FALSE);
-}
-
-static int __init aedsp16_dsp_reset(int port)
-{
-	/*
-	 * Reset DSP
-	 */
-
-	DBG(("Reset DSP:\n"));
-
-	outb(1, (port + DSP_RESET));
-	udelay(10);
-	outb(0, (port + DSP_RESET));
-	udelay(10);
-	udelay(10);
-	if (aedsp16_test_dsp(port) == TRUE) {
-		DBG(("success.\n"));
-		return TRUE;
-	} else
-		DBG(("failure.\n"));
-	return FALSE;
-}
-
-static int __init aedsp16_write(int port, int cmd)
-{
-	unsigned char   ret;
-	int             loop = HARDRETRY;
-
-	DBG(("    Write DSP Byte (0x%x) [0x%x]: ", port, cmd));
-
-	do {
-		ret = inb(port + DSP_STATUS);
-		/*
-		 * DSP ready to receive data if bit 7 of ret == 0
-		 */
-		if (!(ret & 0x80)) {
-			outb(cmd, port + DSP_COMMAND);
-			DBG(("success.\n"));
-			return 0;
-		}
-	} while (loop--);
-
-	DBG(("timeout.\n"));
-	printk("[AEDSP16] DSP Command (0x%x) timeout.\n", cmd);
-
-	return -1;
-}
-
-#if defined(CONFIG_SC6600)
-
-#if defined(AEDSP16_INFO) || defined(AEDSP16_DEBUG)
-void __init aedsp16_pinfo(void) {
-	DBG(("\n Base address:  %x\n", decoded_hcfg.iobase));
-	DBG((" Joystick    : %s present\n", decoded_hcfg.joystick?"":" not"));
-	DBG((" WSS addr    :  %x\n", decoded_hcfg.wssbase));
-	DBG((" MPU-401 addr:  %x\n", decoded_hcfg.mpubase));
-	DBG((" CDROM       : %s present\n", (decoded_hcfg.cdrom!=4)?"":" not"));
-	DBG((" CDROMADDR   :  %x\n\n", decoded_hcfg.cdrombase));
-}
-#endif
-
-void __init aedsp16_hard_decode(void) {
-
-	DBG((" aedsp16_hard_decode: 0x%x, 0x%x\n", hard_cfg[0], hard_cfg[1]));
-
-/*
- * Decode Cfg Bytes.
- */
-	decoded_hcfg.iobase	= IOBASE(hard_cfg[0]);
-	decoded_hcfg.joystick	= JOY(hard_cfg[0]);
-	decoded_hcfg.wssbase	= WSSADDR(hard_cfg[0]);
-	decoded_hcfg.mpubase	= MPUADDR(hard_cfg[0]);
-	decoded_hcfg.cdrom	= CDROM(hard_cfg[1]);
-	decoded_hcfg.cdrombase	= CDROMADDR(hard_cfg[1]);
-
-#if defined(AEDSP16_INFO) || defined(AEDSP16_DEBUG)
-	printk(" Original sound card configuration:\n");
-	aedsp16_pinfo();
-#endif
-
-/*
- * Now set up the real kernel configuration.
- */
-	decoded_hcfg.iobase	= ae_config.base_io;
-	decoded_hcfg.wssbase	= ae_config.mss_base;
-	decoded_hcfg.mpubase	= ae_config.mpu_base;
-
-#if defined(CONFIG_SC6600_JOY)
- 	decoded_hcfg.joystick	= CONFIG_SC6600_JOY; /* Enable */
-#endif
-#if defined(CONFIG_SC6600_CDROM)
-	decoded_hcfg.cdrom	= CONFIG_SC6600_CDROM; /* 4:N-3:I-2:G-1:P-0:S */
-#endif
-#if defined(CONFIG_SC6600_CDROMBASE)
-	decoded_hcfg.cdrombase	= CONFIG_SC6600_CDROMBASE; /* 0 Disable */
-#endif
-
-#if defined(AEDSP16_DEBUG)
-	DBG((" New Values:\n"));
-	aedsp16_pinfo();
-#endif
-
-	DBG(("success.\n"));
-}
-
-void __init aedsp16_hard_encode(void) {
-
-	DBG((" aedsp16_hard_encode: 0x%x, 0x%x\n", hard_cfg[0], hard_cfg[1]));
-
-	hard_cfg[0] = 0;
-	hard_cfg[1] = 0;
-
-	hard_cfg[0] |= 0x20;
-
-	BLDIOBASE (hard_cfg[0], decoded_hcfg.iobase);
-	BLDWSSADDR(hard_cfg[0], decoded_hcfg.wssbase);
-	BLDMPUADDR(hard_cfg[0], decoded_hcfg.mpubase);
-	BLDJOY(hard_cfg[0], decoded_hcfg.joystick);
-	BLDCDROM(hard_cfg[1], decoded_hcfg.cdrom);
-	BLDCDROMADDR(hard_cfg[1], decoded_hcfg.cdrombase);
-
-#if defined(AEDSP16_DEBUG)
-	aedsp16_pinfo();
-#endif
-
-	DBG((" aedsp16_hard_encode: 0x%x, 0x%x\n", hard_cfg[0], hard_cfg[1]));
-	DBG(("success.\n"));
-
-}
-
-static int __init aedsp16_hard_write(int port) {
-
-	DBG(("aedsp16_hard_write:\n"));
-
-	if (aedsp16_write(port, COMMAND_6C)) {
-		printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_6C);
-		DBG(("failure.\n"));
-		return FALSE;
-	}
-	if (aedsp16_write(port, COMMAND_5C)) {
-		printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_5C);
-		DBG(("failure.\n"));
-		return FALSE;
-	}
-	if (aedsp16_write(port, hard_cfg[0])) {
-		printk("[AEDSP16] DATA 0x%x: failed!\n", hard_cfg[0]);
-		DBG(("failure.\n"));
-		return FALSE;
-	}
-	if (aedsp16_write(port, hard_cfg[1])) {
-		printk("[AEDSP16] DATA 0x%x: failed!\n", hard_cfg[1]);
-		DBG(("failure.\n"));
-		return FALSE;
-	}
-	if (aedsp16_write(port, COMMAND_C5)) {
-		printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_C5);
-		DBG(("failure.\n"));
-		return FALSE;
-	}
-
-	DBG(("success.\n"));
-
-	return TRUE;
-}
-
-static int __init aedsp16_hard_read(int port) {
-
-	DBG(("aedsp16_hard_read:\n"));
-
-	if (aedsp16_write(port, READ_HARD_CFG)) {
-		printk("[AEDSP16] CMD 0x%x: failed!\n", READ_HARD_CFG);
-		DBG(("failure.\n"));
-		return FALSE;
-	}
-
-	if ((hard_cfg[0] = aedsp16_read(port)) == -1) {
-		printk("[AEDSP16] aedsp16_read after CMD 0x%x: failed\n",
-			READ_HARD_CFG);
-		DBG(("failure.\n"));
-		return FALSE;
-	}
-	if ((hard_cfg[1] = aedsp16_read(port)) == -1) {
-		printk("[AEDSP16] aedsp16_read after CMD 0x%x: failed\n",
-			READ_HARD_CFG);
-		DBG(("failure.\n"));
-		return FALSE;
-	}
-	if (aedsp16_read(port) == -1) {
-		printk("[AEDSP16] aedsp16_read after CMD 0x%x: failed\n",
-			READ_HARD_CFG);
-		DBG(("failure.\n"));
-		return FALSE;
-	}
-
-	DBG(("success.\n"));
-
-	return TRUE;
-}
-
-static int __init aedsp16_ext_cfg_write(int port) {
-
-	int extcfg, val;
-
-	if (aedsp16_write(port, COMMAND_66)) {
-		printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_66);
-		return FALSE;
-	}
-
-	extcfg = 7;
-	if (decoded_hcfg.cdrom != 2)
-		extcfg = 0x0F;
-	if ((decoded_hcfg.cdrom == 4) ||
-	    (decoded_hcfg.cdrom == 3))
-		extcfg &= ~2;
-	if (decoded_hcfg.cdrombase == 0)
-		extcfg &= ~2;
-	if (decoded_hcfg.mpubase == 0)
-		extcfg &= ~1;
-
-	if (aedsp16_write(port, extcfg)) {
-		printk("[AEDSP16] Write extcfg: failed!\n");
-		return FALSE;
-	}
-	if (aedsp16_write(port, 0)) {
-		printk("[AEDSP16] Write extcfg: failed!\n");
-		return FALSE;
-	}
-	if (decoded_hcfg.cdrom == 3) {
-		if (aedsp16_write(port, COMMAND_52)) {
-			printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_52);
-			return FALSE;
-		}
-		if ((val = aedsp16_read(port)) == -1) {
-			printk("[AEDSP16] aedsp16_read after CMD 0x%x: failed\n"
-					, COMMAND_52);
-			return FALSE;
-		}
-		val &= 0x7F;
-		if (aedsp16_write(port, COMMAND_60)) {
-			printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_60);
-			return FALSE;
-		}
-		if (aedsp16_write(port, val)) {
-			printk("[AEDSP16] Write val: failed!\n");
-			return FALSE;
-		}
-	}
-
-	return TRUE;
-}
-
-#endif /* CONFIG_SC6600 */
-
-static int __init aedsp16_cfg_write(int port) {
-	if (aedsp16_write(port, WRITE_MDIRQ_CFG)) {
-		printk("[AEDSP16] CMD 0x%x: failed!\n", WRITE_MDIRQ_CFG);
-		return FALSE;
-	}
-	if (aedsp16_write(port, soft_cfg)) {
-		printk("[AEDSP16] Initialization of (M)IRQ and DMA: failed!\n");
-		return FALSE;
-	}
-	return TRUE;
-}
-
-static int __init aedsp16_init_mss(int port)
-{
-	DBG(("aedsp16_init_mss:\n"));
-
-	mdelay(10);
-
-	if (aedsp16_write(port, DSP_INIT_MSS)) {
-		printk("[AEDSP16] aedsp16_init_mss [0x%x]: failed!\n",
-				DSP_INIT_MSS);
-		DBG(("failure.\n"));
-		return FALSE;
-	}
-	
-	mdelay(10);
-
-	if (aedsp16_cfg_write(port) == FALSE)
-		return FALSE;
-
-	outb(soft_cfg_mss, ae_config.mss_base);
-
-	DBG(("success.\n"));
-
-	return TRUE;
-}
-
-static int __init aedsp16_setup_board(int port) {
-	int	loop = RETRY;
-
-#if defined(CONFIG_SC6600)
-	int	val = 0;
-
-	if (aedsp16_hard_read(port) == FALSE) {
-		printk("[AEDSP16] aedsp16_hard_read: failed!\n");
-		return FALSE;
-	}
-
-	if (aedsp16_write(port, COMMAND_52)) {
-		printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_52);
-		return FALSE;
-	}
-
-	if ((val = aedsp16_read(port)) == -1) {
-		printk("[AEDSP16] aedsp16_read after CMD 0x%x: failed\n",
-				COMMAND_52);
-		return FALSE;
-	}
-#endif
-
-	do {
-		if (aedsp16_write(port, COMMAND_88)) {
-			printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_88);
-			return FALSE;
-		}
-		mdelay(10);
-	} while ((aedsp16_wait_data(port) == FALSE) && loop--);
-
-	if (aedsp16_read(port) == -1) {
-		printk("[AEDSP16] aedsp16_read after CMD 0x%x: failed\n",
-				COMMAND_88);
-		return FALSE;
-	}
-
-#if !defined(CONFIG_SC6600)
-	if (aedsp16_write(port, COMMAND_5C)) {
-		printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_5C);
-		return FALSE;
-	}
-#endif
-
-	if (aedsp16_cfg_write(port) == FALSE)
-		return FALSE;
-
-#if defined(CONFIG_SC6600)
-	if (aedsp16_write(port, COMMAND_60)) {
-		printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_60);
-		return FALSE;
-	}
-	if (aedsp16_write(port, val)) {
-		printk("[AEDSP16] DATA 0x%x: failed!\n", val);
-		return FALSE;
-	}
-	if (aedsp16_write(port, COMMAND_6E)) {
-		printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_6E);
-		return FALSE;
-	}
-	if (aedsp16_write(port, ver[0])) {
-		printk("[AEDSP16] DATA 0x%x: failed!\n", ver[0]);
-		return FALSE;
-	}
-	if (aedsp16_write(port, ver[1])) {
-		printk("[AEDSP16] DATA 0x%x: failed!\n", ver[1]);
-		return FALSE;
-	}
-
-	if (aedsp16_hard_write(port) == FALSE) {
-		printk("[AEDSP16] aedsp16_hard_write: failed!\n");
-		return FALSE;
-	}
-
-	if (aedsp16_write(port, COMMAND_5C)) {
-		printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_5C);
-		return FALSE;
-	}
-
-#if defined(THIS_IS_A_THING_I_HAVE_NOT_TESTED_YET)
-	if (aedsp16_cfg_write(port) == FALSE)
-		return FALSE;
-#endif
-
-#endif
-
-	return TRUE;
-}
-
-static int __init aedsp16_stdcfg(int port) {
-	if (aedsp16_write(port, WRITE_MDIRQ_CFG)) {
-		printk("[AEDSP16] CMD 0x%x: failed!\n", WRITE_MDIRQ_CFG);
-		return FALSE;
-	}
-	/*
-	 * 0x0A == (IRQ 7, DMA 1, MIRQ 0)
-	 */
-	if (aedsp16_write(port, 0x0A)) {
-		printk("[AEDSP16] aedsp16_stdcfg: failed!\n");
-		return FALSE;
-	}
-	return TRUE;
-}
-
-static int __init aedsp16_dsp_version(int port)
-{
-	int             len = 0;
-	int             ret;
-
-	DBG(("Get DSP Version:\n"));
-
-	if (aedsp16_write(ae_config.base_io, GET_DSP_VERSION)) {
-		printk("[AEDSP16] CMD 0x%x: failed!\n", GET_DSP_VERSION);
-		DBG(("failed.\n"));
-		return FALSE;
-	}
-
-	do {
-		if ((ret = aedsp16_read(port)) == -1) {
-			DBG(("failed.\n"));
-			return FALSE;
-		}
-	/*
-	 * We already know how many int are stored (2), so we know when the
-	 * string is finished.
-	 */
-		ver[len++] = ret;
-	  } while (len < CARDVERLEN);
-	sprintf(DSPVersion, "%d.%d", ver[0], ver[1]);
-
-	DBG(("success.\n"));
-
-	return TRUE;
-}
-
-static int __init aedsp16_dsp_copyright(int port)
-{
-	int             len = 0;
-	int             ret;
-
-	DBG(("Get DSP Copyright:\n"));
-
-	if (aedsp16_write(ae_config.base_io, GET_DSP_COPYRIGHT)) {
-		printk("[AEDSP16] CMD 0x%x: failed!\n", GET_DSP_COPYRIGHT);
-		DBG(("failed.\n"));
-		return FALSE;
-	}
-
-	do {
-		if ((ret = aedsp16_read(port)) == -1) {
-	/*
-	 * If no more data available, return to the caller, no error if len>0.
-	 * We have no other way to know when the string is finished.
-	 */
-			if (len)
-				break;
-			else {
-				DBG(("failed.\n"));
-				return FALSE;
-			}
-		}
-
-		DSPCopyright[len++] = ret;
-
-	  } while (len < CARDNAMELEN);
-
-	DBG(("success.\n"));
-
-	return TRUE;
-}
-
-static void __init aedsp16_init_tables(void)
-{
-	int i = 0;
-
-	memset(DSPCopyright, 0, CARDNAMELEN + 1);
-	memset(DSPVersion, 0, CARDVERLEN + 1);
-
-	for (i = 0; orIRQ[i].or; i++)
-		if (orIRQ[i].val == ae_config.irq) {
-			soft_cfg |= orIRQ[i].or;
-			soft_cfg_mss |= orIRQ[i].or;
-		}
-
-	for (i = 0; orMIRQ[i].or; i++)
-		if (orMIRQ[i].or == ae_config.mpu_irq)
-			soft_cfg |= orMIRQ[i].or;
-
-	for (i = 0; orDMA[i].or; i++)
-		if (orDMA[i].val == ae_config.dma) {
-			soft_cfg |= orDMA[i].or;
-			soft_cfg_mss |= orDMA[i].or;
-		}
-}
-
-static int __init aedsp16_init_board(void)
-{
-	aedsp16_init_tables();
-
-	if (aedsp16_dsp_reset(ae_config.base_io) == FALSE) {
-		printk("[AEDSP16] aedsp16_dsp_reset: failed!\n");
-		return FALSE;
-	}
-	if (aedsp16_dsp_copyright(ae_config.base_io) == FALSE) {
-		printk("[AEDSP16] aedsp16_dsp_copyright: failed!\n");
-		return FALSE;
-	}
-
-	/*
-	 * My AEDSP16 card return SC-6000 in DSPCopyright, so
-	 * if we have something different, we have to be warned.
-	 */
-	if (strcmp("SC-6000", DSPCopyright))
-		printk("[AEDSP16] Warning: non SC-6000 audio card!\n");
-
-	if (aedsp16_dsp_version(ae_config.base_io) == FALSE) {
-		printk("[AEDSP16] aedsp16_dsp_version: failed!\n");
-		return FALSE;
-	}
-
-	if (aedsp16_stdcfg(ae_config.base_io) == FALSE) {
-		printk("[AEDSP16] aedsp16_stdcfg: failed!\n");
-		return FALSE;
-	}
-
-#if defined(CONFIG_SC6600)
-	if (aedsp16_hard_read(ae_config.base_io) == FALSE) {
-		printk("[AEDSP16] aedsp16_hard_read: failed!\n");
-		return FALSE;
-	}
-
-	aedsp16_hard_decode();
-
-	aedsp16_hard_encode();
-
-	if (aedsp16_hard_write(ae_config.base_io) == FALSE) {
-		printk("[AEDSP16] aedsp16_hard_write: failed!\n");
-		return FALSE;
-	}
-
-	if (aedsp16_ext_cfg_write(ae_config.base_io) == FALSE) {
-		printk("[AEDSP16] aedsp16_ext_cfg_write: failed!\n");
-		return FALSE;
-	}
-#endif /* CONFIG_SC6600 */
-
-	if (aedsp16_setup_board(ae_config.base_io) == FALSE) {
-		printk("[AEDSP16] aedsp16_setup_board: failed!\n");
-		return FALSE;
-	}
-
-	if (ae_config.mss_base != -1) {
-		if (ae_config.init & INIT_MSS) {
-			if (aedsp16_init_mss(ae_config.base_io) == FALSE) {
-				printk("[AEDSP16] Can not initialize"
-				       "Microsoft Sound System mode.\n");
-				return FALSE;
-			}
-		}
-	}
-
-#if !defined(MODULE) || defined(AEDSP16_INFO) || defined(AEDSP16_DEBUG)
-
-	printk("Audio Excel DSP 16 init v%s (%s %s) [",
-		VERSION, DSPCopyright,
-		DSPVersion);
-
-	if (ae_config.mpu_base != -1) {
-		if (ae_config.init & INIT_MPU401) {
-			printk("MPU401");
-			if ((ae_config.init & INIT_MSS) ||
-			    (ae_config.init & INIT_SBPRO))
-				printk(" ");
-		}
-	}
-
-	if (ae_config.mss_base == -1) {
-		if (ae_config.init & INIT_SBPRO) {
-			printk("SBPro");
-			if (ae_config.init & INIT_MSS)
-				printk(" ");
-		}
-	}
-
-	if (ae_config.mss_base != -1)
-		if (ae_config.init & INIT_MSS)
-			printk("MSS");
-
-	printk("]\n");
-#endif /* MODULE || AEDSP16_INFO || AEDSP16_DEBUG */
-
-	mdelay(10);
-
-	return TRUE;
-}
-
-static int __init init_aedsp16_sb(void)
-{
-	DBG(("init_aedsp16_sb: "));
-
-/*
- * If the card is already init'ed MSS, we can not init it to SBPRO too
- * because the board can not emulate simultaneously MSS and SBPRO.
- */
-	if (ae_config.init & INIT_MSS)
-		return FALSE;
-	if (ae_config.init & INIT_SBPRO)
-		return FALSE;
-
-	ae_config.init |= INIT_SBPRO;
-
-	DBG(("done.\n"));
-
-	return TRUE;
-}
-
-static void __init uninit_aedsp16_sb(void)
-{
-	DBG(("uninit_aedsp16_sb: "));
-
-	ae_config.init &= ~INIT_SBPRO;
-
-	DBG(("done.\n"));
-}
-
-static int __init init_aedsp16_mss(void)
-{
-	DBG(("init_aedsp16_mss: "));
-
-/*
- * If the card is already init'ed SBPRO, we can not init it to MSS too
- * because the board can not emulate simultaneously MSS and SBPRO.
- */
-	if (ae_config.init & INIT_SBPRO)
-		return FALSE;
-	if (ae_config.init & INIT_MSS)
-		return FALSE;
-/*
- * We must check the CONFIG_AEDSP16_BASE region too because these are the I/O 
- * ports to access card's control registers.
- */
-	if (!(ae_config.init & INIT_MPU401)) {
-		if (check_region(ae_config.base_io, IOBASE_REGION_SIZE)) {
-			printk(
-			"AEDSP16 BASE I/O port region is already in use.\n");
-			return FALSE;
-		}
-	}
-
-/*
- * We must allocate the CONFIG_AEDSP16_BASE region too because these are the 
- * I/O ports to access card's control registers.
- */
-	if (!(ae_config.init & INIT_MPU401))
-		request_region(ae_config.base_io, IOBASE_REGION_SIZE,
-				"aedsp16 (base)");
-
-	ae_config.init |= INIT_MSS;
-
-	DBG(("done.\n"));
-
-	return TRUE;
-}
-
-static void __init uninit_aedsp16_mss(void)
-{
-	DBG(("uninit_aedsp16_mss: "));
-
-	if ((!(ae_config.init & INIT_MPU401)) &&
-	   (ae_config.init & INIT_MSS)) {
-		release_region(ae_config.base_io, IOBASE_REGION_SIZE);
-		DBG(("AEDSP16 base region released.\n"));
-	}
-
-	ae_config.init &= ~INIT_MSS;
-	DBG(("done.\n"));
-}
-
-static int __init init_aedsp16_mpu(void)
-{
-	DBG(("init_aedsp16_mpu: "));
-
-	if (ae_config.init & INIT_MPU401)
-		return FALSE;
-
-/*
- * We must check the CONFIG_AEDSP16_BASE region too because these are the I/O 
- * ports to access card's control registers.
- */
-	if (!(ae_config.init & (INIT_MSS | INIT_SBPRO))) {
-		if (check_region(ae_config.base_io, IOBASE_REGION_SIZE)) {
-			printk(
-			"AEDSP16 BASE I/O port region is already in use.\n");
-			return FALSE;
-		}
-	}
-
-	if (!(ae_config.init & (INIT_MSS | INIT_SBPRO)))
-		request_region(ae_config.base_io, IOBASE_REGION_SIZE,
-				"aedsp16 (base)");
-
-	ae_config.init |= INIT_MPU401;
-
-	DBG(("done.\n"));
-
-	return TRUE;
-}
-
-static void __init uninit_aedsp16_mpu(void)
-{
-	DBG(("uninit_aedsp16_mpu: "));
-
-	if ((!(ae_config.init & (INIT_MSS | INIT_SBPRO))) &&
-	   (ae_config.init & INIT_MPU401)) {
-		release_region(ae_config.base_io, IOBASE_REGION_SIZE);
-		DBG(("AEDSP16 base region released.\n"));
-	}
-
-	ae_config.init &= ~INIT_MPU401;
-
-	DBG(("done.\n"));
-}
-
-int __init init_aedsp16(void)
-{
-	int initialized = FALSE;
-
-#if !defined(MODULE)
-	ae_config.base_io = CONFIG_AEDSP16_BASE;
-#if defined(CONFIG_AEDSP16_SBPRO)
-	ae_config.irq = CONFIG_AEDSP16_SB_IRQ;
-	ae_config.dma = CONFIG_AEDSP16_SB_DMA;
-#endif
-#if defined(CONFIG_AEDSP16_MSS)
-	ae_config.mss_base = CONFIG_MSS_BASE;
-	ae_config.irq = CONFIG_AEDSP16_MSS_IRQ;
-	ae_config.dma = CONFIG_AEDSP16_MSS_DMA;
-#endif
-#if defined(CONFIG_AEDSP16_MPU401)
-	ae_config.mpu_base = CONFIG_MPU_BASE;
-	ae_config.mpu_irq = CONFIG_AEDSP16_MPU_IRQ;
-#endif
-#endif /* !MODULE */
-	DBG(("Initializing BASE[0x%x] IRQ[%d] DMA[%d] MIRQ[%d]\n",
-	     ae_config.base_io,ae_config.irq,ae_config.dma,ae_config.mpu_irq));
-
-	if (ae_config.mss_base == -1) {
-		if (init_aedsp16_sb() == FALSE) {
-			uninit_aedsp16_sb();
-		} else {
-			initialized = TRUE;
-		}
-	}
-
-	if (ae_config.mpu_base != -1) {
-		if (init_aedsp16_mpu() == FALSE) {
-			uninit_aedsp16_mpu();
-		} else {
-			initialized = TRUE;
-		}
-	}
-
-/*
- * In the sequence of init routines, the MSS init MUST be the last!
- * This because of the special register programming the MSS mode needs.
- * A board reset would disable the MSS mode restoring the default SBPRO
- * mode.
- */
-	if (ae_config.mss_base != -1) {
-		if (init_aedsp16_mss() == FALSE) {
-			uninit_aedsp16_mss();
-		} else {
-			initialized = TRUE;
-		}
-	}
-
-	if (initialized)
-		initialized = aedsp16_init_board();
-	return initialized;
-}
-
-void __init uninit_aedsp16(void)
-{
-	if (ae_config.mss_base != -1)
-		uninit_aedsp16_mss();
-	else
-		uninit_aedsp16_sb();
-	if (ae_config.mpu_base != -1)
-		uninit_aedsp16_mpu();
-}
-
-#if defined(MODULE)
-
-int io = -1;
-int irq = -1;
-int dma = -1;
-int mpu_irq = -1;
-int mss_base = -1;
-int mpu_base = -1;
-
-
-MODULE_PARM(io, "i");
-MODULE_PARM_DESC(io, "I/O base address (0x220 0x240)");
-MODULE_PARM(irq, "i");
-MODULE_PARM_DESC(irq, "IRQ line (5 7 9 10 11)");
-MODULE_PARM(dma, "i");
-MODULE_PARM_DESC(dma, "dma line (0 1 3)");
-MODULE_PARM(mpu_irq, "i");
-MODULE_PARM_DESC(mpu_irq, "MPU-401 IRQ line (5 7 9 10 0)");
-MODULE_PARM(mss_base, "i");
-MODULE_PARM_DESC(mss_base, "MSS emulation I/O base address (0x530 0xE80)");
-MODULE_PARM(mpu_base, "i");
-MODULE_PARM_DESC(mpu_base,"MPU-401 I/O base address (0x300 0x310 0x320 0x330)");
-MODULE_AUTHOR("Riccardo Facchetti <fizban@tin.it>");
-MODULE_DESCRIPTION("Audio Excel DSP 16 Driver Version " VERSION);
-
-int init_module(void) {
-	printk("Audio Excel DSP 16 init driver Copyright (C) Riccardo Facchetti 1995-98\n");
-	if (io == -1 || dma == -1 || irq == -1) {
-		printk(KERN_INFO "aedsp16: I/O, IRQ and DMA are mandatory\n");
-		return -EINVAL;
-	}
-
-	ae_config.base_io = io;
-	ae_config.irq = irq;
-	ae_config.dma = dma;
-
-	ae_config.mss_base = mss_base;
-	ae_config.mpu_base = mpu_base;
-	ae_config.mpu_irq = mpu_irq;
-
-	if (init_aedsp16() == FALSE) {
-		printk(KERN_ERR "aedsp16: initialization failed\n");
-		/*
-		 * XXX
-		 * What error should we return here ?
-		 */
-		return -EINVAL;
-	}
-	SOUND_LOCK;
-	return 0;
-}
-
-void cleanup_module(void) {
-	uninit_aedsp16();
-	SOUND_LOCK_END;
-}
-#endif /* MODULE */
-
-#endif /* CONFIG_AEDSP16 */

FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)