patch-2.4.10 linux/arch/sh/kernel/io_7751se.c

• Lines: 305
• Date: Sat Sep 8 12:29:09 2001
• Orig file: v2.4.9/linux/arch/sh/kernel/io_7751se.c
• Orig date: Wed Dec 31 16:00:00 1969

diff -u --recursive --new-file v2.4.9/linux/arch/sh/kernel/io_7751se.c linux/arch/sh/kernel/io_7751se.c
@@ -0,0 +1,304 @@
+/* 
+ * linux/arch/sh/kernel/io_7751se.c
+ *
+ * Copyright (C) 2001  Ian da Silva, Jeremy Siegel
+ * Based largely on io_se.c.
+ *
+ * I/O routine for Hitachi 7751 SolutionEngine.
+ *
+ * Initial version only to support LAN access; some
+ * placeholder code from io_se.c left in with the
+ * expectation of later SuperIO and PCMCIA access.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <asm/io.h>
+#include <asm/hitachi_7751se.h>
+#include <asm/addrspace.h>
+
+#include <asm/pci.h>
+#include <asm/pci-sh7751.h>
+
+#if 0
+/******************************************************************
+ * Variables from io_se.c, related to PCMCIA (not PCI); we're not
+ * compiling them in, and have removed references from functions
+ * which follow.  [Many checked for IO ports in the range bounded
+ * by sh_pcic_io_start/stop, and used sh_pcic_io_wbase as offset.
+ * As start/stop are uninitialized, only port 0x0 would match?]
+ * When used, remember to adjust names to avoid clash with io_se?
+ *****************************************************************/
+/* SH pcmcia io window base, start and end.  */
+int sh_pcic_io_wbase = 0xb8400000;
+int sh_pcic_io_start;
+int sh_pcic_io_stop;
+int sh_pcic_io_type;
+int sh_pcic_io_dummy;
+/*************************************************************/
+#endif
+
+/*
+ * The 7751 Solution Engine uses the built-in PCI controller (PCIC)
+ * of the 7751 processor, and has a SuperIO accessible via the PCI.
+ * The board also includes a PCMCIA controller on its memory bus,
+ * like the other Solution Engine boards.
+ */ 
+
+#define PCIIOBR		(volatile long *)PCI_REG(SH7751_PCIIOBR)
+#define PCIMBR          (volatile long *)PCI_REG(SH7751_PCIMBR)
+#define PCI_IO_AREA	SH7751_PCI_IO_BASE
+#define PCI_MEM_AREA	SH7751_PCI_CONFIG_BASE
+
+#define PCI_IOMAP(adr)	(PCI_IO_AREA + (adr & ~SH7751_PCIIOBR_MASK))
+
+#define maybebadio(name,port) \
+  printk("bad PC-like io %s for port 0x%lx at 0x%08x\n", \
+	 #name, (port), (__u32) __builtin_return_address(0))
+
+static inline void delay(void)
+{
+	ctrl_inw(0xa0000000);
+}
+
+static inline volatile __u16 *
+port2adr(unsigned int port)
+{
+	if (port >= 0x2000)
+		return (volatile __u16 *) (PA_MRSHPC + (port - 0x2000));
+#if 0
+	else
+		return (volatile __u16 *) (PA_SUPERIO + (port << 1));
+#endif
+	maybebadio(name,port);
+	return (volatile __u16*)port;
+}
+
+#if 0
+/* The 7751 Solution Engine seems to have everything hooked */
+/* up pretty normally (nothing on high-bytes only...) so this */
+/* shouldn't be needed */
+static inline int
+shifted_port(unsigned long port)
+{
+	/* For IDE registers, value is not shifted */
+	if ((0x1f0 <= port && port < 0x1f8) || port == 0x3f6)
+		return 0;
+	else
+		return 1;
+}
+#endif
+
+/* In case someone configures the kernel w/o PCI support: in that */
+/* scenario, don't ever bother to check for PCI-window addresses */
+
+/* NOTE: WINDOW CHECK MAY BE A BIT OFF, HIGH PCIBIOS_MIN_IO WRAPS? */
+#if defined(CONFIG_PCI)
+#define CHECK_SH7751_PCIIO(port) \
+  ((port >= PCIBIOS_MIN_IO) && (port < (PCIBIOS_MIN_IO + SH7751_PCI_IO_SIZE)))
+#else
+#define CHECK_SH_7751_PCIIO(port) (0)
+#endif
+
+/*
+ * General outline: remap really low stuff [eventually] to SuperIO,
+ * stuff in PCI IO space (at or above window at pci.h:PCIBIOS_MIN_IO)
+ * is mapped through the PCI IO window.  Stuff with high bits (PXSEG)
+ * should be way beyond the window, and is used  w/o translation for
+ * compatibility.
+ */
+unsigned char sh7751se_inb(unsigned long port)
+{
+	if (PXSEG(port))
+		return *(volatile unsigned char *)port;
+	else if (CHECK_SH7751_PCIIO(port))
+		return *(volatile unsigned char *)PCI_IOMAP(port);
+	else
+		return (*port2adr(port))&0xff; 
+}
+
+unsigned char sh7751se_inb_p(unsigned long port)
+{
+	unsigned char v;
+
+        if (PXSEG(port))
+                v = *(volatile unsigned char *)port;
+	else if (CHECK_SH7751_PCIIO(port))
+                v = *(volatile unsigned char *)PCI_IOMAP(port);
+	else
+		v = (*port2adr(port))&0xff; 
+	delay();
+	return v;
+}
+
+unsigned short sh7751se_inw(unsigned long port)
+{
+        if (PXSEG(port))
+                return *(volatile unsigned short *)port;
+	else if (CHECK_SH7751_PCIIO(port))
+                return *(volatile unsigned short *)PCI_IOMAP(port);
+	else if (port >= 0x2000)
+		return *port2adr(port);
+	else
+		maybebadio(inw, port);
+	return 0;
+}
+
+unsigned int sh7751se_inl(unsigned long port)
+{
+        if (PXSEG(port))
+                return *(volatile unsigned long *)port;
+	else if (CHECK_SH7751_PCIIO(port))
+                return *(volatile unsigned int *)PCI_IOMAP(port);
+	else if (port >= 0x2000)
+		return *port2adr(port);
+	else
+		maybebadio(inl, port);
+	return 0;
+}
+
+void sh7751se_outb(unsigned char value, unsigned long port)
+{
+
+        if (PXSEG(port))
+                *(volatile unsigned char *)port = value;
+	else if (CHECK_SH7751_PCIIO(port))
+        	*((unsigned char*)PCI_IOMAP(port)) = value;
+	else
+		*(port2adr(port)) = value;
+}
+
+void sh7751se_outb_p(unsigned char value, unsigned long port)
+{
+        if (PXSEG(port))
+                *(volatile unsigned char *)port = value;
+	else if (CHECK_SH7751_PCIIO(port))
+        	*((unsigned char*)PCI_IOMAP(port)) = value;
+	else
+		*(port2adr(port)) = value;
+	delay();
+}
+
+void sh7751se_outw(unsigned short value, unsigned long port)
+{
+        if (PXSEG(port))
+                *(volatile unsigned short *)port = value;
+	else if (CHECK_SH7751_PCIIO(port))
+        	*((unsigned short *)PCI_IOMAP(port)) = value;
+	else if (port >= 0x2000)
+		*port2adr(port) = value;
+	else
+		maybebadio(outw, port);
+}
+
+void sh7751se_outl(unsigned int value, unsigned long port)
+{
+        if (PXSEG(port))
+                *(volatile unsigned long *)port = value;
+	else if (CHECK_SH7751_PCIIO(port))
+        	*((unsigned long*)PCI_IOMAP(port)) = value;
+	else
+		maybebadio(outl, port);
+}
+
+void sh7751se_insb(unsigned long port, void *addr, unsigned long count)
+{
+	unsigned char *p = addr;
+	while (count--) *p++ = sh7751se_inb(port);
+}
+
+void sh7751se_insw(unsigned long port, void *addr, unsigned long count)
+{
+	unsigned short *p = addr;
+	while (count--) *p++ = sh7751se_inw(port);
+}
+
+void sh7751se_insl(unsigned long port, void *addr, unsigned long count)
+{
+	maybebadio(insl, port);
+}
+
+void sh7751se_outsb(unsigned long port, const void *addr, unsigned long count)
+{
+	unsigned char *p = (unsigned char*)addr;
+	while (count--) sh7751se_outb(*p++, port);
+}
+
+void sh7751se_outsw(unsigned long port, const void *addr, unsigned long count)
+{
+	unsigned short *p = (unsigned short*)addr;
+	while (count--) sh7751se_outw(*p++, port);
+}
+
+void sh7751se_outsl(unsigned long port, const void *addr, unsigned long count)
+{
+	maybebadio(outsw, port);
+}
+
+/* For read/write calls, just copy generic (pass-thru); PCIMBR is  */
+/* already set up.  For a larger memory space, these would need to */
+/* reset PCIMBR as needed on a per-call basis...                   */
+
+unsigned char sh7751se_readb(unsigned long addr)
+{
+	return *(volatile unsigned char*)addr;
+}
+
+unsigned short sh7751se_readw(unsigned long addr)
+{
+	return *(volatile unsigned short*)addr;
+}
+
+unsigned int sh7751se_readl(unsigned long addr)
+{
+	return *(volatile unsigned long*)addr;
+}
+
+void sh7751se_writeb(unsigned char b, unsigned long addr)
+{
+	*(volatile unsigned char*)addr = b;
+}
+
+void sh7751se_writew(unsigned short b, unsigned long addr)
+{
+	*(volatile unsigned short*)addr = b;
+}
+
+void sh7751se_writel(unsigned int b, unsigned long addr)
+{
+        *(volatile unsigned long*)addr = b;
+}
+
+
+
+/* Map ISA bus address to the real address. Only for PCMCIA.  */
+
+/* ISA page descriptor.  */
+static __u32 sh_isa_memmap[256];
+
+static int
+sh_isa_mmap(__u32 start, __u32 length, __u32 offset)
+{
+	int idx;
+
+	if (start >= 0x100000 || (start & 0xfff) || (length != 0x1000))
+		return -1;
+
+	idx = start >> 12;
+	sh_isa_memmap[idx] = 0xb8000000 + (offset &~ 0xfff);
+#if 0
+	printk("sh_isa_mmap: start %x len %x offset %x (idx %x paddr %x)\n",
+	       start, length, offset, idx, sh_isa_memmap[idx]);
+#endif
+	return 0;
+}
+
+unsigned long
+sh7751se_isa_port2addr(unsigned long offset)
+{
+	int idx;
+
+	idx = (offset >> 12) & 0xff;
+	offset &= 0xfff;
+	return sh_isa_memmap[idx] + offset;
+}