patch-2.4.2 linux/include/asm-arm/arch-sa1100/graphicsclient.h

• Lines: 89
• Date: Thu Feb 8 16:32:44 2001
• Orig file: v2.4.1/linux/include/asm-arm/arch-sa1100/graphicsclient.h
• Orig date: Wed Dec 31 16:00:00 1969

diff -u --recursive --new-file v2.4.1/linux/include/asm-arm/arch-sa1100/graphicsclient.h linux/include/asm-arm/arch-sa1100/graphicsclient.h
@@ -0,0 +1,88 @@
+/*
+ * linux/include/asm-arm/arch-sa1100/graphicsclient.h
+ *
+ * Created 2000/06/11 by Nicolas Pitre <nico@cam.org>
+ * Modified 7/27/00 by Woojung <whuh@applieddata.net>
+ *
+ * This file contains the hardware specific definitions for the 
+ * ADS GraphicsClient/ThinClient boards.
+ */
+
+#ifndef __ASM_ARCH_HARDWARE_H
+#error "include <asm/hardware.h> instead"
+#endif
+
+
+#define ADS_CPLD_BASE		(0x10000000)
+#define ADS_p2v( x )		((x) - ADS_CPLD_BASE + 0xf0000000)
+#define ADS_v2p( x )		((x) - 0xf0000000 + ADS_CPLD_BASE)
+
+
+/* Parallel Port */
+
+#define _ADS_PPDR		0x10020000	/* parallel port data reg */
+#define _ADS_PPSR		0x10020004	/* parallel port status reg */
+
+
+/* PCMCIA */
+
+#define _ADS_CS_STATUS		0x10040000	/* PCMCIA status reg */
+#define ADS_CS_ST_A_READY	(1 << 0)	/* Socket A Card Ready */
+#define ADS_CS_ST_A_CD		(1 << 2)	/* Socket A Card Detect */
+#define ADS_CS_ST_A_BUSY	(1 << 4)	/* Socket A Card Busy */
+#define ADS_CS_ST_A_STS		(1 << 6)	/* Socket A Card STS */
+
+#define _ADS_CS_PR		0x10040004	/* PCMCIA Power/Reset */
+#define ADS_CS_PR_A_5V_POWER	(1 << 0)	/* Socket A Enable 5V Power */
+#define ADS_CS_PR_A_3V_POWER	(1 << 0)	/* Socket A Enable 3.3V Power */
+#define ADS_CS_PR_A_RESET		(1 << 2)	/* Socket A Reset */
+
+
+#define _ADS_SW_SWITCHES	0x10060000	/* Software Switches */
+
+
+/* Extra IRQ Controller */
+
+#define _ADS_INT_ST1		0x10080000	/* IRQ Status #1 */
+#define _ADS_INT_ST2		0x10080004	/* IRQ Status #2 */
+#define _ADS_INT_EN1		0x10080008	/* IRQ Enable #1 */
+#define _ADS_INT_EN2		0x1008000c	/* IRQ Enable #2 */
+
+/* Discrete Controller (AVR:Atmel AT90LS8535) */
+#define _ADS_AVR_REG		0x10080018
+
+/* On-Board Ethernet */
+
+#define _ADS_ETHERNET		0x100e0000	/* Ethernet */
+
+
+/* Extra UARTs */
+
+#define _ADS_UARTA		0x10100000	/* UART A */
+#define _ADS_UARTB		0x10120000	/* UART B */
+#define _ADS_UARTC		0x10140000	/* UART C */
+#define _ADS_UARTD		0x10160000	/* UART D */
+
+
+/* LEDs */
+
+#define ADS_LED0	GPIO_GPIO20		/* on-board D22 */
+#define ADS_LED1	GPIO_GPIO21		/* on-board D21 */
+#define ADS_LED2	GPIO_GPIO22		/* on-board D20 */
+#define ADS_LED3	GPIO_GPIO23		/* external */
+#define ADS_LED4	GPIO_GPIO24		/* external */
+#define ADS_LED5	GPIO_GPIO25		/* external */
+#define ADS_LED6	GPIO_GPIO26		/* external */
+#define ADS_LED7	GPIO_GPIO27		/* external */
+
+
+/* Virtual register addresses */
+
+#ifndef __ASSEMBLY__
+#define ADS_INT_ST1	(*((volatile u_char *) ADS_p2v(_ADS_INT_ST1)))
+#define ADS_INT_ST2	(*((volatile u_char *) ADS_p2v(_ADS_INT_ST2)))
+#define ADS_INT_EN1	(*((volatile u_char *) ADS_p2v(_ADS_INT_EN1)))
+#define ADS_INT_EN2	(*((volatile u_char *) ADS_p2v(_ADS_INT_EN2)))
+#define ADS_ETHERNET	((int) ADS_p2v(_ADS_ETHERNET))
+#define ADS_AVR_REG	(*((volatile u_char *) ADS_p2v(_ADS_AVR_REG)))
+#endif