patch-2.4.23 linux-2.4.23/drivers/net/e1000/e1000_hw.h
Next file: linux-2.4.23/drivers/net/e1000/e1000_main.c
Previous file: linux-2.4.23/drivers/net/e1000/e1000_hw.c
Back to the patch index
Back to the overall index
- Lines: 679
- Date:
2003-11-28 10:26:20.000000000 -0800
- Orig file:
linux-2.4.22/drivers/net/e1000/e1000_hw.h
- Orig date:
2003-08-25 04:44:42.000000000 -0700
diff -urN linux-2.4.22/drivers/net/e1000/e1000_hw.h linux-2.4.23/drivers/net/e1000/e1000_hw.h
@@ -33,9 +33,9 @@
#ifndef _E1000_HW_H_
#define _E1000_HW_H_
-
#include "e1000_osdep.h"
+
/* Forward declarations of structures used by the shared code */
struct e1000_hw;
struct e1000_hw_stats;
@@ -50,9 +50,13 @@
e1000_82544,
e1000_82540,
e1000_82545,
+ e1000_82545_rev_3,
e1000_82546,
+ e1000_82546_rev_3,
e1000_82541,
+ e1000_82541_rev_2,
e1000_82547,
+ e1000_82547_rev_2,
e1000_num_macs
} e1000_mac_type;
@@ -67,6 +71,7 @@
typedef enum {
e1000_media_type_copper = 0,
e1000_media_type_fiber = 1,
+ e1000_media_type_internal_serdes = 2,
e1000_num_media_types
} e1000_media_type;
@@ -90,7 +95,8 @@
typedef enum {
e1000_bus_type_unknown = 0,
e1000_bus_type_pci,
- e1000_bus_type_pcix
+ e1000_bus_type_pcix,
+ e1000_bus_type_reserved
} e1000_bus_type;
/* PCI bus speeds */
@@ -108,7 +114,8 @@
typedef enum {
e1000_bus_width_unknown = 0,
e1000_bus_width_32,
- e1000_bus_width_64
+ e1000_bus_width_64,
+ e1000_bus_width_reserved
} e1000_bus_width;
/* PHY status info structure and supporting enums */
@@ -186,6 +193,26 @@
e1000_phy_undefined = 0xFF
} e1000_phy_type;
+typedef enum {
+ e1000_ms_hw_default = 0,
+ e1000_ms_force_master,
+ e1000_ms_force_slave,
+ e1000_ms_auto
+} e1000_ms_type;
+
+typedef enum {
+ e1000_ffe_config_enabled = 0,
+ e1000_ffe_config_active,
+ e1000_ffe_config_blocked
+} e1000_ffe_config;
+
+typedef enum {
+ e1000_dsp_config_disabled = 0,
+ e1000_dsp_config_enabled,
+ e1000_dsp_config_activated,
+ e1000_dsp_config_undefined = 0xFF
+} e1000_dsp_config;
+
struct e1000_phy_info {
e1000_cable_length cable_length;
e1000_10bt_ext_dist_enable extended_10bt_distance;
@@ -224,9 +251,10 @@
/* Function prototypes */
/* Initialization */
-void e1000_reset_hw(struct e1000_hw *hw);
+int32_t e1000_reset_hw(struct e1000_hw *hw);
int32_t e1000_init_hw(struct e1000_hw *hw);
int32_t e1000_set_mac_type(struct e1000_hw *hw);
+void e1000_set_media_type(struct e1000_hw *hw);
/* Link Configuration */
int32_t e1000_setup_link(struct e1000_hw *hw);
@@ -234,8 +262,9 @@
void e1000_config_collision_dist(struct e1000_hw *hw);
int32_t e1000_config_fc_after_link_up(struct e1000_hw *hw);
int32_t e1000_check_for_link(struct e1000_hw *hw);
-void e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t * speed, uint16_t * duplex);
+int32_t e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t * speed, uint16_t * duplex);
int32_t e1000_wait_autoneg(struct e1000_hw *hw);
+int32_t e1000_force_mac_fc(struct e1000_hw *hw);
/* PHY */
int32_t e1000_read_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *phy_data);
@@ -292,6 +321,8 @@
uint32_t e1000_read_reg_io(struct e1000_hw *hw, uint32_t offset);
void e1000_io_write(struct e1000_hw *hw, uint32_t port, uint32_t value);
void e1000_write_reg_io(struct e1000_hw *hw, uint32_t offset, uint32_t value);
+int32_t e1000_config_dsp_after_link_change(struct e1000_hw *hw, boolean_t link_up);
+int32_t e1000_set_d3_lplu_state(struct e1000_hw *hw, boolean_t active);
#define E1000_READ_REG_IO(a, reg) \
e1000_read_reg_io((a), E1000_##reg)
@@ -313,13 +344,22 @@
#define E1000_DEV_ID_82540EP_LP 0x101E
#define E1000_DEV_ID_82545EM_COPPER 0x100F
#define E1000_DEV_ID_82545EM_FIBER 0x1011
+#define E1000_DEV_ID_82545GM_COPPER 0x1026
+#define E1000_DEV_ID_82545GM_FIBER 0x1027
+#define E1000_DEV_ID_82545GM_SERDES 0x1028
#define E1000_DEV_ID_82546EB_COPPER 0x1010
#define E1000_DEV_ID_82546EB_FIBER 0x1012
#define E1000_DEV_ID_82546EB_QUAD_COPPER 0x101D
#define E1000_DEV_ID_82541EI 0x1013
-#define E1000_DEV_ID_82541EP 0x1018
+#define E1000_DEV_ID_82541EI_MOBILE 0x1018
+#define E1000_DEV_ID_82541ER 0x1078
+#define E1000_DEV_ID_82547GI 0x1075
+#define E1000_DEV_ID_82541GI 0x1076
+#define E1000_DEV_ID_82541GI_MOBILE 0x1077
+#define E1000_DEV_ID_82546GB_COPPER 0x1079
+#define E1000_DEV_ID_82546GB_FIBER 0x107A
+#define E1000_DEV_ID_82546GB_SERDES 0x107B
#define E1000_DEV_ID_82547EI 0x1019
-#define NUM_DEV_IDS 20
#define NODE_ADDRESS_SIZE 6
#define ETH_LENGTH_OF_ADDRESS 6
@@ -385,7 +425,7 @@
E1000_IMS_RXSEQ | \
E1000_IMS_LSC)
-/* The number of high/low register pairs in the RAR. The RAR (Receive Address
+/* Number of high/low register pairs in the RAR. The RAR (Receive Address
* Registers) holds the directed and multicast addresses that we monitor. We
* reserve one of these spots for our directed address, allowing us room for
* E1000_RAR_ENTRIES - 1 multicast addresses.
@@ -539,7 +579,7 @@
volatile uint32_t high; /* receive address high */
};
-/* The number of entries in the Multicast Table Array (MTA). */
+/* Number of entries in the Multicast Table Array (MTA). */
#define E1000_NUM_MTA_REGISTERS 128
/* IPv4 Address Table Entry */
@@ -599,6 +639,7 @@
* A - register array
*/
#define E1000_CTRL 0x00000 /* Device Control - RW */
+#define E1000_CTRL_DUP 0x00004 /* Device Control Duplicate (Shadow) - RW */
#define E1000_STATUS 0x00008 /* Device Status - RO */
#define E1000_EECD 0x00010 /* EEPROM/Flash Control - RW */
#define E1000_EERD 0x00014 /* EEPROM Read - RW */
@@ -934,6 +975,9 @@
e1000_bus_width bus_width;
e1000_bus_type bus_type;
struct e1000_eeprom_info eeprom;
+ e1000_ms_type master_slave;
+ e1000_ms_type original_master_slave;
+ e1000_ffe_config ffe_config_state;
uint32_t io_base;
uint32_t phy_id;
uint32_t phy_revision;
@@ -950,6 +994,7 @@
uint32_t ledctl_default;
uint32_t ledctl_mode1;
uint32_t ledctl_mode2;
+ uint16_t phy_spd_default;
uint16_t autoneg_advertised;
uint16_t pci_cmd_word;
uint16_t fc_high_water;
@@ -974,10 +1019,13 @@
uint8_t perm_mac_addr[NODE_ADDRESS_SIZE];
boolean_t disable_polarity_correction;
boolean_t speed_downgraded;
+ e1000_dsp_config dsp_config_state;
boolean_t get_link_status;
boolean_t tbi_compatibility_en;
boolean_t tbi_compatibility_on;
+ boolean_t phy_reset_disable;
boolean_t fc_send_xon;
+ boolean_t fc_strict_ieee;
boolean_t report_tx_early;
boolean_t adaptive_ifs;
boolean_t ifs_params_forced;
@@ -1059,7 +1107,7 @@
#define E1000_EECD_PRES 0x00000100 /* EEPROM Present */
#define E1000_EECD_SIZE 0x00000200 /* EEPROM Size (0=64 word 1=256 word) */
#define E1000_EECD_ADDR_BITS 0x00000400 /* EEPROM Addressing bits based on type
- * (0-small, 1-large) */
+ * (0-small, 1-large) */
#define E1000_EECD_TYPE 0x00002000 /* EEPROM Type (1-SPI, 0-Microwire) */
#ifndef E1000_EEPROM_GRANT_ATTEMPTS
#define E1000_EEPROM_GRANT_ATTEMPTS 1000 /* EEPROM # attempts to gain grant */
@@ -1121,22 +1169,22 @@
#define E1000_MDIC_ERROR 0x40000000
/* LED Control */
-#define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F
-#define E1000_LEDCTL_LED0_MODE_SHIFT 0
-#define E1000_LEDCTL_LED0_IVRT 0x00000040
-#define E1000_LEDCTL_LED0_BLINK 0x00000080
-#define E1000_LEDCTL_LED1_MODE_MASK 0x00000F00
-#define E1000_LEDCTL_LED1_MODE_SHIFT 8
-#define E1000_LEDCTL_LED1_IVRT 0x00004000
-#define E1000_LEDCTL_LED1_BLINK 0x00008000
-#define E1000_LEDCTL_LED2_MODE_MASK 0x000F0000
-#define E1000_LEDCTL_LED2_MODE_SHIFT 16
-#define E1000_LEDCTL_LED2_IVRT 0x00400000
-#define E1000_LEDCTL_LED2_BLINK 0x00800000
-#define E1000_LEDCTL_LED3_MODE_MASK 0x0F000000
-#define E1000_LEDCTL_LED3_MODE_SHIFT 24
-#define E1000_LEDCTL_LED3_IVRT 0x40000000
-#define E1000_LEDCTL_LED3_BLINK 0x80000000
+#define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F
+#define E1000_LEDCTL_LED0_MODE_SHIFT 0
+#define E1000_LEDCTL_LED0_IVRT 0x00000040
+#define E1000_LEDCTL_LED0_BLINK 0x00000080
+#define E1000_LEDCTL_LED1_MODE_MASK 0x00000F00
+#define E1000_LEDCTL_LED1_MODE_SHIFT 8
+#define E1000_LEDCTL_LED1_IVRT 0x00004000
+#define E1000_LEDCTL_LED1_BLINK 0x00008000
+#define E1000_LEDCTL_LED2_MODE_MASK 0x000F0000
+#define E1000_LEDCTL_LED2_MODE_SHIFT 16
+#define E1000_LEDCTL_LED2_IVRT 0x00400000
+#define E1000_LEDCTL_LED2_BLINK 0x00800000
+#define E1000_LEDCTL_LED3_MODE_MASK 0x0F000000
+#define E1000_LEDCTL_LED3_MODE_SHIFT 24
+#define E1000_LEDCTL_LED3_IVRT 0x40000000
+#define E1000_LEDCTL_LED3_BLINK 0x80000000
#define E1000_LEDCTL_MODE_LINK_10_1000 0x0
#define E1000_LEDCTL_MODE_LINK_100_1000 0x1
@@ -1159,109 +1207,109 @@
#define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */
/* Interrupt Cause Read */
-#define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */
-#define E1000_ICR_TXQE 0x00000002 /* Transmit Queue empty */
-#define E1000_ICR_LSC 0x00000004 /* Link Status Change */
-#define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */
-#define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */
-#define E1000_ICR_RXO 0x00000040 /* rx overrun */
-#define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */
-#define E1000_ICR_MDAC 0x00000200 /* MDIO access complete */
-#define E1000_ICR_RXCFG 0x00000400 /* RX /c/ ordered set */
-#define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */
-#define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */
-#define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */
-#define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */
-#define E1000_ICR_TXD_LOW 0x00008000
-#define E1000_ICR_SRPD 0x00010000
+#define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */
+#define E1000_ICR_TXQE 0x00000002 /* Transmit Queue empty */
+#define E1000_ICR_LSC 0x00000004 /* Link Status Change */
+#define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */
+#define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */
+#define E1000_ICR_RXO 0x00000040 /* rx overrun */
+#define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */
+#define E1000_ICR_MDAC 0x00000200 /* MDIO access complete */
+#define E1000_ICR_RXCFG 0x00000400 /* RX /c/ ordered set */
+#define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */
+#define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */
+#define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */
+#define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */
+#define E1000_ICR_TXD_LOW 0x00008000
+#define E1000_ICR_SRPD 0x00010000
/* Interrupt Cause Set */
-#define E1000_ICS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
-#define E1000_ICS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
-#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
-#define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
-#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
-#define E1000_ICS_RXO E1000_ICR_RXO /* rx overrun */
-#define E1000_ICS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
-#define E1000_ICS_MDAC E1000_ICR_MDAC /* MDIO access complete */
-#define E1000_ICS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
-#define E1000_ICS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
-#define E1000_ICS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
-#define E1000_ICS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
-#define E1000_ICS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
-#define E1000_ICS_TXD_LOW E1000_ICR_TXD_LOW
-#define E1000_ICS_SRPD E1000_ICR_SRPD
+#define E1000_ICS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
+#define E1000_ICS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
+#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
+#define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
+#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
+#define E1000_ICS_RXO E1000_ICR_RXO /* rx overrun */
+#define E1000_ICS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
+#define E1000_ICS_MDAC E1000_ICR_MDAC /* MDIO access complete */
+#define E1000_ICS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
+#define E1000_ICS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
+#define E1000_ICS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
+#define E1000_ICS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
+#define E1000_ICS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
+#define E1000_ICS_TXD_LOW E1000_ICR_TXD_LOW
+#define E1000_ICS_SRPD E1000_ICR_SRPD
/* Interrupt Mask Set */
-#define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
-#define E1000_IMS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
-#define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */
-#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
-#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
-#define E1000_IMS_RXO E1000_ICR_RXO /* rx overrun */
-#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
-#define E1000_IMS_MDAC E1000_ICR_MDAC /* MDIO access complete */
-#define E1000_IMS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
-#define E1000_IMS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
-#define E1000_IMS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
-#define E1000_IMS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
-#define E1000_IMS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
-#define E1000_IMS_TXD_LOW E1000_ICR_TXD_LOW
-#define E1000_IMS_SRPD E1000_ICR_SRPD
+#define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
+#define E1000_IMS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
+#define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */
+#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
+#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
+#define E1000_IMS_RXO E1000_ICR_RXO /* rx overrun */
+#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
+#define E1000_IMS_MDAC E1000_ICR_MDAC /* MDIO access complete */
+#define E1000_IMS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
+#define E1000_IMS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
+#define E1000_IMS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
+#define E1000_IMS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
+#define E1000_IMS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
+#define E1000_IMS_TXD_LOW E1000_ICR_TXD_LOW
+#define E1000_IMS_SRPD E1000_ICR_SRPD
/* Interrupt Mask Clear */
-#define E1000_IMC_TXDW E1000_ICR_TXDW /* Transmit desc written back */
-#define E1000_IMC_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
-#define E1000_IMC_LSC E1000_ICR_LSC /* Link Status Change */
-#define E1000_IMC_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
-#define E1000_IMC_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
-#define E1000_IMC_RXO E1000_ICR_RXO /* rx overrun */
-#define E1000_IMC_RXT0 E1000_ICR_RXT0 /* rx timer intr */
-#define E1000_IMC_MDAC E1000_ICR_MDAC /* MDIO access complete */
-#define E1000_IMC_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
-#define E1000_IMC_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
-#define E1000_IMC_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
-#define E1000_IMC_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
-#define E1000_IMC_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
-#define E1000_IMC_TXD_LOW E1000_ICR_TXD_LOW
-#define E1000_IMC_SRPD E1000_ICR_SRPD
+#define E1000_IMC_TXDW E1000_ICR_TXDW /* Transmit desc written back */
+#define E1000_IMC_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
+#define E1000_IMC_LSC E1000_ICR_LSC /* Link Status Change */
+#define E1000_IMC_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
+#define E1000_IMC_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
+#define E1000_IMC_RXO E1000_ICR_RXO /* rx overrun */
+#define E1000_IMC_RXT0 E1000_ICR_RXT0 /* rx timer intr */
+#define E1000_IMC_MDAC E1000_ICR_MDAC /* MDIO access complete */
+#define E1000_IMC_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
+#define E1000_IMC_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
+#define E1000_IMC_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
+#define E1000_IMC_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
+#define E1000_IMC_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
+#define E1000_IMC_TXD_LOW E1000_ICR_TXD_LOW
+#define E1000_IMC_SRPD E1000_ICR_SRPD
/* Receive Control */
-#define E1000_RCTL_RST 0x00000001 /* Software reset */
-#define E1000_RCTL_EN 0x00000002 /* enable */
-#define E1000_RCTL_SBP 0x00000004 /* store bad packet */
-#define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */
-#define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */
-#define E1000_RCTL_LPE 0x00000020 /* long packet enable */
-#define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */
-#define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */
-#define E1000_RCTL_LBM_SLP 0x00000080 /* serial link loopback mode */
-#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
-#define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */
-#define E1000_RCTL_RDMTS_QUAT 0x00000100 /* rx desc min threshold size */
-#define E1000_RCTL_RDMTS_EIGTH 0x00000200 /* rx desc min threshold size */
-#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
-#define E1000_RCTL_MO_0 0x00000000 /* multicast offset 11:0 */
-#define E1000_RCTL_MO_1 0x00001000 /* multicast offset 12:1 */
-#define E1000_RCTL_MO_2 0x00002000 /* multicast offset 13:2 */
-#define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */
-#define E1000_RCTL_MDR 0x00004000 /* multicast desc ring 0 */
-#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
+#define E1000_RCTL_RST 0x00000001 /* Software reset */
+#define E1000_RCTL_EN 0x00000002 /* enable */
+#define E1000_RCTL_SBP 0x00000004 /* store bad packet */
+#define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */
+#define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */
+#define E1000_RCTL_LPE 0x00000020 /* long packet enable */
+#define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */
+#define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */
+#define E1000_RCTL_LBM_SLP 0x00000080 /* serial link loopback mode */
+#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
+#define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */
+#define E1000_RCTL_RDMTS_QUAT 0x00000100 /* rx desc min threshold size */
+#define E1000_RCTL_RDMTS_EIGTH 0x00000200 /* rx desc min threshold size */
+#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
+#define E1000_RCTL_MO_0 0x00000000 /* multicast offset 11:0 */
+#define E1000_RCTL_MO_1 0x00001000 /* multicast offset 12:1 */
+#define E1000_RCTL_MO_2 0x00002000 /* multicast offset 13:2 */
+#define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */
+#define E1000_RCTL_MDR 0x00004000 /* multicast desc ring 0 */
+#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
/* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */
-#define E1000_RCTL_SZ_2048 0x00000000 /* rx buffer size 2048 */
-#define E1000_RCTL_SZ_1024 0x00010000 /* rx buffer size 1024 */
-#define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */
-#define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */
+#define E1000_RCTL_SZ_2048 0x00000000 /* rx buffer size 2048 */
+#define E1000_RCTL_SZ_1024 0x00010000 /* rx buffer size 1024 */
+#define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */
+#define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */
/* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */
-#define E1000_RCTL_SZ_16384 0x00010000 /* rx buffer size 16384 */
-#define E1000_RCTL_SZ_8192 0x00020000 /* rx buffer size 8192 */
-#define E1000_RCTL_SZ_4096 0x00030000 /* rx buffer size 4096 */
-#define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */
-#define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */
-#define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */
-#define E1000_RCTL_DPF 0x00400000 /* discard pause frames */
-#define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */
-#define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */
+#define E1000_RCTL_SZ_16384 0x00010000 /* rx buffer size 16384 */
+#define E1000_RCTL_SZ_8192 0x00020000 /* rx buffer size 8192 */
+#define E1000_RCTL_SZ_4096 0x00030000 /* rx buffer size 4096 */
+#define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */
+#define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */
+#define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */
+#define E1000_RCTL_DPF 0x00400000 /* discard pause frames */
+#define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */
+#define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */
/* Receive Descriptor */
#define E1000_RDT_DELAY 0x0000ffff /* Delay timer (1=1024us) */
@@ -1426,15 +1474,17 @@
#define EEPROM_SIZE_128B 0x0000
#define EEPROM_SIZE_MASK 0x1C00
-
/* EEPROM Word Offsets */
-#define EEPROM_COMPAT 0x0003
-#define EEPROM_ID_LED_SETTINGS 0x0004
-#define EEPROM_INIT_CONTROL1_REG 0x000A
-#define EEPROM_INIT_CONTROL2_REG 0x000F
-#define EEPROM_CFG 0x0012
-#define EEPROM_FLASH_VERSION 0x0032
-#define EEPROM_CHECKSUM_REG 0x003F
+#define EEPROM_COMPAT 0x0003
+#define EEPROM_ID_LED_SETTINGS 0x0004
+#define EEPROM_SERDES_AMPLITUDE 0x0006 /* For SERDES output amplitude adjustment. */
+#define EEPROM_INIT_CONTROL1_REG 0x000A
+#define EEPROM_INIT_CONTROL2_REG 0x000F
+#define EEPROM_INIT_CONTROL3_PORT_B 0x0014
+#define EEPROM_INIT_CONTROL3_PORT_A 0x0024
+#define EEPROM_CFG 0x0012
+#define EEPROM_FLASH_VERSION 0x0032
+#define EEPROM_CHECKSUM_REG 0x003F
/* Word definitions for ID LED Settings */
#define ID_LED_RESERVED_0000 0x0000
@@ -1458,6 +1508,9 @@
#define IGP_LED3_MODE 0x07000000
+/* Mask bits for SERDES amplitude adjustment in Word 6 of the EEPROM */
+#define EEPROM_SERDES_AMPLITUDE_MASK 0x000F
+
/* Mask bits for fields in Word 0x0a of the EEPROM */
#define EEPROM_WORD0A_ILOS 0x0010
#define EEPROM_WORD0A_SWDPIO 0x01E0
@@ -1479,6 +1532,8 @@
#define EEPROM_NODE_ADDRESS_BYTE_0 0
#define EEPROM_PBA_BYTE_1 8
+#define EEPROM_RESERVED_WORD 0xFFFF
+
/* EEPROM Map Sizes (Byte Counts) */
#define PBA_SIZE 4
@@ -1490,7 +1545,7 @@
#define E1000_HDX_COLLISION_DISTANCE E1000_COLLISION_DISTANCE
#define E1000_COLD_SHIFT 12
-/* The number of Transmit and Receive Descriptors must be a multiple of 8 */
+/* Number of Transmit and Receive Descriptors must be a multiple of 8 */
#define REQ_TX_DESCRIPTOR_MULTIPLE 8
#define REQ_RX_DESCRIPTOR_MULTIPLE 8
@@ -1557,35 +1612,30 @@
#define PCIX_STATUS_HI_MMRBC_2K 0x2
-/* The number of bits that we need to shift right to move the "pause"
- * bits from the EEPROM (bits 13:12) to the "pause" (bits 8:7) field
- * in the TXCW register
+/* Number of bits required to shift right the "pause" bits from the
+ * EEPROM (bits 13:12) to the "pause" (bits 8:7) field in the TXCW register.
*/
#define PAUSE_SHIFT 5
-/* The number of bits that we need to shift left to move the "SWDPIO"
- * bits from the EEPROM (bits 8:5) to the "SWDPIO" (bits 25:22) field
- * in the CTRL register
+/* Number of bits required to shift left the "SWDPIO" bits from the
+ * EEPROM (bits 8:5) to the "SWDPIO" (bits 25:22) field in the CTRL register.
*/
#define SWDPIO_SHIFT 17
-/* The number of bits that we need to shift left to move the "SWDPIO_EXT"
- * bits from the EEPROM word F (bits 7:4) to the bits 11:8 of The
- * Extended CTRL register.
- * in the CTRL register
+/* Number of bits required to shift left the "SWDPIO_EXT" bits from the
+ * EEPROM word F (bits 7:4) to the bits 11:8 of The Extended CTRL register.
*/
#define SWDPIO__EXT_SHIFT 4
-/* The number of bits that we need to shift left to move the "ILOS"
- * bit from the EEPROM (bit 4) to the "ILOS" (bit 7) field
- * in the CTRL register
+/* Number of bits required to shift left the "ILOS" bit from the EEPROM
+ * (bit 4) to the "ILOS" (bit 7) field in the CTRL register.
*/
#define ILOS_SHIFT 3
#define RECEIVE_BUFFER_ALIGN_SIZE (256)
-/* The number of milliseconds we wait for auto-negotiation to complete */
+/* Number of milliseconds we wait for auto-negotiation to complete */
#define LINK_UP_TIMEOUT 500
#define E1000_TX_BUFFER_SIZE ((uint32_t)1514)
@@ -1668,7 +1718,16 @@
#define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */
#define M88E1000_RX_ERR_CNTR 0x15 /* Receive Error Counter */
+#define M88E1000_PHY_EXT_CTRL 0x1A /* PHY extend control register */
+#define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */
+#define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */
+#define M88E1000_PHY_VCO_REG_BIT8 0x100 /* Bits 8 & 11 are adjusted for */
+#define M88E1000_PHY_VCO_REG_BIT11 0x800 /* improved BER performance */
+
#define IGP01E1000_IEEE_REGS_PAGE 0x0000
+#define IGP01E1000_IEEE_RESTART_AUTONEG 0x3300
+#define IGP01E1000_IEEE_FORCE_GIGA 0x0140
+
/* IGP01E1000 Specific Registers */
#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* PHY Specific Port Config Register */
#define IGP01E1000_PHY_PORT_STATUS 0x11 /* PHY Specific Status Register */
@@ -1684,17 +1743,35 @@
#define IGP01E1000_PHY_AGC_C 0x1472
#define IGP01E1000_PHY_AGC_D 0x1872
-/* Number of AGC registers */
-#define IGP01E1000_PHY_AGC_NUM 4
+/* IGP01E1000 DSP Reset Register */
+#define IGP01E1000_PHY_DSP_RESET 0x1F33
+#define IGP01E1000_PHY_DSP_SET 0x1F71
+#define IGP01E1000_PHY_DSP_FFE 0x1F35
+
+#define IGP01E1000_PHY_CHANNEL_NUM 4
+#define IGP01E1000_PHY_AGC_PARAM_A 0x1171
+#define IGP01E1000_PHY_AGC_PARAM_B 0x1271
+#define IGP01E1000_PHY_AGC_PARAM_C 0x1471
+#define IGP01E1000_PHY_AGC_PARAM_D 0x1871
+
+#define IGP01E1000_PHY_EDAC_MU_INDEX 0xC000
+#define IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS 0x8000
+
+#define IGP01E1000_PHY_ANALOG_TX_STATE 0x2890
+#define IGP01E1000_PHY_ANALOG_CLASS_A 0x2000
+#define IGP01E1000_PHY_FORCE_ANALOG_ENABLE 0x0004
+#define IGP01E1000_PHY_DSP_FFE_CM_CP 0x0069
+#define IGP01E1000_PHY_DSP_FFE_DEFAULT 0x002A
/* IGP01E1000 PCS Initialization register - stores the polarity status when
* speed = 1000 Mbps. */
#define IGP01E1000_PHY_PCS_INIT_REG 0x00B4
+#define IGP01E1000_PHY_PCS_CTRL_REG 0x00B5
#define IGP01E1000_ANALOG_REGS_PAGE 0x20C0
#define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */
-
+#define MAX_PHY_MULTI_PAGE_REG 0xF /*Registers that are equal on all pages*/
/* PHY Control Register */
#define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */
#define MII_CR_COLL_TEST_ENABLE 0x0080 /* Collision test enable */
@@ -1808,8 +1885,11 @@
#define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */
#define SR_1000T_MS_CONFIG_RES 0x4000 /* 1=Local TX is Master, 0=Slave */
#define SR_1000T_MS_CONFIG_FAULT 0x8000 /* Master/Slave config fault */
-#define SR_1000T_REMOTE_RX_STATUS_SHIFT 12
-#define SR_1000T_LOCAL_RX_STATUS_SHIFT 13
+#define SR_1000T_REMOTE_RX_STATUS_SHIFT 12
+#define SR_1000T_LOCAL_RX_STATUS_SHIFT 13
+#define SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT 5
+#define FFE_IDLE_ERR_COUNT_TIMEOUT_20 20
+#define FFE_IDLE_ERR_COUNT_TIMEOUT_100 100
/* Extended Status Register */
#define IEEE_ESR_1000T_HD_CAPS 0x1000 /* 1000T HD capable */
@@ -1901,7 +1981,6 @@
#define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */
#define M88E1000_EPSCR_TX_CLK_0 0x0000 /* NO TX_CLK */
-
/* IGP01E1000 Specific Port Config Register - R/W */
#define IGP01E1000_PSCFR_AUTO_MDIX_PAR_DETECT 0x0010
#define IGP01E1000_PSCFR_PRE_EN 0x0020
@@ -1952,6 +2031,11 @@
#define IGP01E1000_MSE_CHANNEL_B 0x0F00
#define IGP01E1000_MSE_CHANNEL_A 0xF000
+/* IGP01E1000 DSP reset macros */
+#define DSP_RESET_ENABLE 0x0
+#define DSP_RESET_DISABLE 0x2
+#define E1000_MAX_DSP_RESETS 10
+
/* IGP01E1000 AGC Registers */
#define IGP01E1000_AGC_LENGTH_SHIFT 7 /* Coarse - 13:11, Fine - 10:7 */
@@ -1962,18 +2046,6 @@
/* The precision of the length is +/- 10 meters */
#define IGP01E1000_AGC_RANGE 10
-/* IGP cable length table */
-static const
-uint16_t e1000_igp_cable_length_table[IGP01E1000_AGC_LENGTH_TABLE_SIZE] =
- { 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
- 5, 10, 10, 10, 10, 10, 10, 10, 20, 20, 20, 20, 20, 25, 25, 25,
- 25, 25, 25, 25, 30, 30, 30, 30, 40, 40, 40, 40, 40, 40, 40, 40,
- 40, 50, 50, 50, 50, 50, 50, 50, 60, 60, 60, 60, 60, 60, 60, 60,
- 60, 70, 70, 70, 70, 70, 70, 80, 80, 80, 80, 80, 80, 90, 90, 90,
- 90, 90, 90, 90, 90, 90, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100,
- 100, 100, 100, 100, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110,
- 110, 110, 110, 110, 110, 110, 120, 120, 120, 120, 120, 120, 120, 120, 120, 120};
-
/* IGP01E1000 PCS Initialization register */
/* bits 3:6 in the PCS registers stores the channels polarity */
#define IGP01E1000_PHY_POLARITY_MASK 0x0078
@@ -1982,11 +2054,12 @@
#define IGP01E1000_GMII_FLEX_SPD 0x10 /* Enable flexible speed
* on Link-Up */
#define IGP01E1000_GMII_SPD 0x20 /* Enable SPD */
+
/* IGP01E1000 Analog Register */
-#define IGP01E1000_ANALOG_SPARE_FUSE_STATUS 0x0011
-#define IGP01E1000_ANALOG_FUSE_STATUS 0x0010
-#define IGP01E1000_ANALOG_FUSE_CONTROL 0x001C
-#define IGP01E1000_ANALOG_FUSE_BYPASS 0x001E
+#define IGP01E1000_ANALOG_SPARE_FUSE_STATUS 0x20D1
+#define IGP01E1000_ANALOG_FUSE_STATUS 0x20D0
+#define IGP01E1000_ANALOG_FUSE_CONTROL 0x20DC
+#define IGP01E1000_ANALOG_FUSE_BYPASS 0x20DE
#define IGP01E1000_ANALOG_FUSE_POLY_MASK 0xF000
#define IGP01E1000_ANALOG_FUSE_FINE_MASK 0x0F80
@@ -2032,5 +2105,7 @@
#define ADVERTISE_1000_HALF 0x0010
#define ADVERTISE_1000_FULL 0x0020
#define AUTONEG_ADVERTISE_SPEED_DEFAULT 0x002F /* Everything but 1000-Half */
+#define AUTONEG_ADVERTISE_10_100_ALL 0x000F /* All 10/100 speeds*/
+#define AUTONEG_ADVERTISE_10_ALL 0x0003 /* 10Mbps Full & Half speeds*/
#endif /* _E1000_HW_H_ */
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)