patch-2.4.23 linux-2.4.23/include/asm-ppc/ppc4xx_dma.h
Next file: linux-2.4.23/include/asm-ppc/ppc_asm.h
Previous file: linux-2.4.23/include/asm-ppc/pgtable.h
Back to the patch index
Back to the overall index
- Lines: 594
- Date:
2003-11-28 10:26:21.000000000 -0800
- Orig file:
linux-2.4.22/include/asm-ppc/ppc4xx_dma.h
- Orig date:
1969-12-31 16:00:00.000000000 -0800
diff -urN linux-2.4.22/include/asm-ppc/ppc4xx_dma.h linux-2.4.23/include/asm-ppc/ppc4xx_dma.h
@@ -0,0 +1,593 @@
+/*
+ * include/asm-ppc/ppc4xx_dma.h
+ *
+ * IBM PPC4xx DMA engine library
+ *
+ * Copyright 2000-2003 MontaVista Software Inc.
+ *
+ * Cleaned by Matt Porter <mporter@mvista.com>
+ *
+ * Original code by Armin Kuster <akuster@mvista.com>
+ * and Pete Popov <ppopov@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifdef __KERNEL__
+#ifndef __ASMPPC_PPC4xx_DMA_H
+#define __ASMPPC_PPC4xx_DMA_H
+
+#include <linux/config.h>
+#include <linux/types.h>
+#include <asm/mmu.h>
+#include <asm/ibm4xx.h>
+
+#undef DEBUG_4xxDMA
+
+#define MAX_PPC4xx_DMA_CHANNELS 4
+
+/* in arch/ppc/kernel/setup.c -- Cort */
+extern unsigned long DMA_MODE_WRITE, DMA_MODE_READ;
+
+/*
+ * Function return status codes
+ * These values are used to indicate whether or not the function
+ * call was successful, or a bad/invalid parameter was passed.
+ */
+#define DMA_STATUS_GOOD 0
+#define DMA_STATUS_BAD_CHANNEL 1
+#define DMA_STATUS_BAD_HANDLE 2
+#define DMA_STATUS_BAD_MODE 3
+#define DMA_STATUS_NULL_POINTER 4
+#define DMA_STATUS_OUT_OF_MEMORY 5
+#define DMA_STATUS_SGL_LIST_EMPTY 6
+#define DMA_STATUS_GENERAL_ERROR 7
+#define DMA_STATUS_CHANNEL_NOTFREE 8
+
+#define DMA_CHANNEL_BUSY 0x80000000
+
+/*
+ * These indicate status as returned from the DMA Status Register.
+ */
+#define DMA_STATUS_NO_ERROR 0
+#define DMA_STATUS_CS 1 /* Count Status */
+#define DMA_STATUS_TS 2 /* Transfer Status */
+#define DMA_STATUS_DMA_ERROR 3 /* DMA Error Occurred */
+#define DMA_STATUS_DMA_BUSY 4 /* The channel is busy */
+
+
+/*
+ * DMA Channel Control Registers
+ */
+
+#ifdef CONFIG_44x
+#define PPC4xx_DMA_64BIT
+#define DMA_CR_OFFSET 1
+#else
+#define DMA_CR_OFFSET 0
+#endif
+
+#define DMA_CE_ENABLE (1<<31) /* DMA Channel Enable */
+#define SET_DMA_CE_ENABLE(x) (((x)&0x1)<<31)
+#define GET_DMA_CE_ENABLE(x) (((x)&DMA_CE_ENABLE)>>31)
+
+#define DMA_CIE_ENABLE (1<<30) /* DMA Channel Interrupt Enable */
+#define SET_DMA_CIE_ENABLE(x) (((x)&0x1)<<30)
+#define GET_DMA_CIE_ENABLE(x) (((x)&DMA_CIE_ENABLE)>>30)
+
+#define DMA_TD (1<<29)
+#define SET_DMA_TD(x) (((x)&0x1)<<29)
+#define GET_DMA_TD(x) (((x)&DMA_TD)>>29)
+
+#define DMA_PL (1<<28) /* Peripheral Location */
+#define SET_DMA_PL(x) (((x)&0x1)<<28)
+#define GET_DMA_PL(x) (((x)&DMA_PL)>>28)
+
+#define EXTERNAL_PERIPHERAL 0
+#define INTERNAL_PERIPHERAL 1
+
+#define SET_DMA_PW(x) (((x)&0x3)<<(26-DMA_CR_OFFSET)) /* Peripheral Width */
+#define DMA_PW_MASK SET_DMA_PW(3)
+#define PW_8 0
+#define PW_16 1
+#define PW_32 2
+#define PW_64 3
+/* FIXME: Add PW_128 support for 440GP DMA block */
+#define GET_DMA_PW(x) (((x)&DMA_PW_MASK)>>(26-DMA_CR_OFFSET))
+
+#define DMA_DAI (1<<(25-DMA_CR_OFFSET)) /* Destination Address Increment */
+#define SET_DMA_DAI(x) (((x)&0x1)<<(25-DMA_CR_OFFSET))
+
+#define DMA_SAI (1<<(24-DMA_CR_OFFSET)) /* Source Address Increment */
+#define SET_DMA_SAI(x) (((x)&0x1)<<(24-DMA_CR_OFFSET))
+
+#define DMA_BEN (1<<(23-DMA_CR_OFFSET)) /* Buffer Enable */
+#define SET_DMA_BEN(x) (((x)&0x1)<<(23-DMA_CR_OFFSET))
+
+#define SET_DMA_TM(x) (((x)&0x3)<<(21-DMA_CR_OFFSET)) /* Transfer Mode */
+#define DMA_TM_MASK SET_DMA_TM(3)
+#define TM_PERIPHERAL 0 /* Peripheral */
+#define TM_RESERVED 1 /* Reserved */
+#define TM_S_MM 2 /* Memory to Memory */
+#define TM_D_MM 3 /* Device Paced Memory to Memory */
+#define GET_DMA_TM(x) (((x)&DMA_TM_MASK)>>(21-DMA_CR_OFFSET))
+
+#define SET_DMA_PSC(x) (((x)&0x3)<<(19-DMA_CR_OFFSET)) /* Peripheral Setup Cycles */
+#define DMA_PSC_MASK SET_DMA_PSC(3)
+#define GET_DMA_PSC(x) (((x)&DMA_PSC_MASK)>>(19-DMA_CR_OFFSET))
+
+#define SET_DMA_PWC(x) (((x)&0x3F)<<(13-DMA_CR_OFFSET)) /* Peripheral Wait Cycles */
+#define DMA_PWC_MASK SET_DMA_PWC(0x3F)
+#define GET_DMA_PWC(x) (((x)&DMA_PWC_MASK)>>(13-DMA_CR_OFFSET))
+
+#define SET_DMA_PHC(x) (((x)&0x7)<<(10-DMA_CR_OFFSET)) /* Peripheral Hold Cycles */
+#define DMA_PHC_MASK SET_DMA_PHC(0x7)
+#define GET_DMA_PHC(x) (((x)&DMA_PHC_MASK)>>(10-DMA_CR_OFFSET))
+
+#define DMA_ETD_OUTPUT (1<<(9-DMA_CR_OFFSET)) /* EOT pin is a TC output */
+#define SET_DMA_ETD(x) (((x)&0x1)<<(9-DMA_CR_OFFSET))
+
+#define DMA_TCE_ENABLE (1<<(8-DMA_CR_OFFSET))
+#define SET_DMA_TCE(x) (((x)&0x1)<<(8-DMA_CR_OFFSET))
+
+#define DMA_DEC (1<<(2) /* Address Decrement */
+#define SET_DMA_DEC(x) (((x)&0x1)<<2)
+#define GET_DMA_DEC(x) (((x)&DMA_DEC)>>2)
+
+/*
+ * Transfer Modes
+ * These modes are defined in a way that makes it possible to
+ * simply "or" in the value in the control register.
+ */
+
+#define DMA_MODE_MM (SET_DMA_TM(TM_S_MM)) /* memory to memory */
+
+ /* Device-paced memory to memory, */
+ /* device is at source address */
+#define DMA_MODE_MM_DEVATSRC (DMA_TD | SET_DMA_TM(TM_D_MM))
+
+ /* Device-paced memory to memory, */
+ /* device is at destination address */
+#define DMA_MODE_MM_DEVATDST (SET_DMA_TM(TM_D_MM))
+
+/* 405gp/440gp */
+#define SET_DMA_PREFETCH(x) (((x)&0x3)<<(4-DMA_CR_OFFSET)) /* Memory Read Prefetch */
+#define DMA_PREFETCH_MASK SET_DMA_PREFETCH(3)
+#define PREFETCH_1 0 /* Prefetch 1 Double Word */
+#define PREFETCH_2 1
+#define PREFETCH_4 2
+#define GET_DMA_PREFETCH(x) (((x)&DMA_PREFETCH_MASK)>>(4-DMA_CR_OFFSET))
+
+#define DMA_PCE (1<<(3-DMA_CR_OFFSET)) /* Parity Check Enable */
+#define SET_DMA_PCE(x) (((x)&0x1)<<(3-DMA_CR_OFFSET))
+#define GET_DMA_PCE(x) (((x)&DMA_PCE)>>(3-DMA_CR_OFFSET))
+
+/* stb3x */
+
+#define DMA_ECE_ENABLE (1<<5)
+#define SET_DMA_ECE(x) (((x)&0x1)<<5)
+#define GET_DMA_ECE(x) (((x)&DMA_ECE_ENABLE)>>5)
+
+#define DMA_TCD_DISABLE (1<<4)
+#define SET_DMA_TCD(x) (((x)&0x1)<<4)
+#define GET_DMA_TCD(x) (((x)&DMA_TCD_DISABLE)>>4)
+
+typedef uint32_t sgl_handle_t;
+
+#ifdef CONFIG_PPC4xx_EDMA
+
+#define SGL_LIST_SIZE 4096
+#define DMA_PPC4xx_SIZE SGL_LIST_SIZE
+
+#define SET_DMA_PRIORITY(x) (((x)&0x3)<<(6-DMA_CR_OFFSET)) /* DMA Channel Priority */
+#define DMA_PRIORITY_MASK SET_DMA_PRIORITY(3)
+#define PRIORITY_LOW 0
+#define PRIORITY_MID_LOW 1
+#define PRIORITY_MID_HIGH 2
+#define PRIORITY_HIGH 3
+#define GET_DMA_PRIORITY(x) (((x)&DMA_PRIORITY_MASK)>>(6-DMA_CR_OFFSET))
+
+/*
+ * DMA Polarity Configuration Register
+ */
+
+#define DMAReq0_ActiveLow (1<<31)
+#define DMAAck0_ActiveLow (1<<30)
+#define EOT0_ActiveLow (1<<29) /* End of Transfer */
+
+#define DMAReq1_ActiveLow (1<<28)
+#define DMAAck1_ActiveLow (1<<27)
+#define EOT1_ActiveLow (1<<26)
+
+#define DMAReq2_ActiveLow (1<<25)
+#define DMAAck2_ActiveLow (1<<24)
+#define EOT2_ActiveLow (1<<23)
+
+#define DMAReq3_ActiveLow (1<<22)
+#define DMAAck3_ActiveLow (1<<21)
+#define EOT3_ActiveLow (1<<20)
+
+/*
+ * DMA Sleep Mode Register
+ */
+#define SLEEP_MODE_ENABLE (1<<21)
+
+/*
+ * DMA Status Register
+ */
+#define DMA_CS0 (1<<31) /* Terminal Count has been reached */
+#define DMA_CS1 (1<<30)
+#define DMA_CS2 (1<<29)
+#define DMA_CS3 (1<<28)
+
+#define DMA_TS0 (1<<27) /* End of Transfer has been requested */
+#define DMA_TS1 (1<<26)
+#define DMA_TS2 (1<<25)
+#define DMA_TS3 (1<<24)
+
+#define DMA_CH0_ERR (1<<23) /* DMA Chanel 0 Error */
+#define DMA_CH1_ERR (1<<22)
+#define DMA_CH2_ERR (1<<21)
+#define DMA_CH3_ERR (1<<20)
+
+#define DMA_IN_DMA_REQ0 (1<<19) /* Internal DMA Request is pending */
+#define DMA_IN_DMA_REQ1 (1<<18)
+#define DMA_IN_DMA_REQ2 (1<<17)
+#define DMA_IN_DMA_REQ3 (1<<16)
+
+#define DMA_EXT_DMA_REQ0 (1<<15) /* External DMA Request is pending */
+#define DMA_EXT_DMA_REQ1 (1<<14)
+#define DMA_EXT_DMA_REQ2 (1<<13)
+#define DMA_EXT_DMA_REQ3 (1<<12)
+
+#define DMA_CH0_BUSY (1<<11) /* DMA Channel 0 Busy */
+#define DMA_CH1_BUSY (1<<10)
+#define DMA_CH2_BUSY (1<<9)
+#define DMA_CH3_BUSY (1<<8)
+
+#define DMA_SG0 (1<<7) /* DMA Channel 0 Scatter/Gather in progress */
+#define DMA_SG1 (1<<6)
+#define DMA_SG2 (1<<5)
+#define DMA_SG3 (1<<4)
+
+/*
+ * DMA SG Command Register
+ */
+#define SSG0_ENABLE (1<<31) /* Start Scatter Gather */
+#define SSG1_ENABLE (1<<30)
+#define SSG2_ENABLE (1<<29)
+#define SSG3_ENABLE (1<<28)
+#define SSG0_MASK_ENABLE (1<<15) /* Enable writing to SSG0 bit */
+#define SSG1_MASK_ENABLE (1<<14)
+#define SSG2_MASK_ENABLE (1<<13)
+#define SSG3_MASK_ENABLE (1<<12)
+
+/*
+ * DMA Scatter/Gather Descriptor Bit fields
+ */
+#define SG_LINK (1<<31) /* Link */
+#define SG_TCI_ENABLE (1<<29) /* Enable Terminal Count Interrupt */
+#define SG_ETI_ENABLE (1<<28) /* Enable End of Transfer Interrupt */
+#define SG_ERI_ENABLE (1<<27) /* Enable Error Interrupt */
+#define SG_COUNT_MASK 0xFFFF /* Count Field */
+
+#define SET_DMA_CONTROL \
+ (SET_DMA_CIE_ENABLE(p_init->int_enable) | /* interrupt enable */ \
+ SET_DMA_BEN(p_init->buffer_enable) | /* buffer enable */\
+ SET_DMA_ETD(p_init->etd_output) | /* end of transfer pin */ \
+ SET_DMA_TCE(p_init->tce_enable) | /* terminal count enable */ \
+ SET_DMA_PL(p_init->pl) | /* peripheral location */ \
+ SET_DMA_DAI(p_init->dai) | /* dest addr increment */ \
+ SET_DMA_SAI(p_init->sai) | /* src addr increment */ \
+ SET_DMA_PRIORITY(p_init->cp) | /* channel priority */ \
+ SET_DMA_PW(p_init->pwidth) | /* peripheral/bus width */ \
+ SET_DMA_PSC(p_init->psc) | /* peripheral setup cycles */ \
+ SET_DMA_PWC(p_init->pwc) | /* peripheral wait cycles */ \
+ SET_DMA_PHC(p_init->phc) | /* peripheral hold cycles */ \
+ SET_DMA_PREFETCH(p_init->pf) /* read prefetch */)
+
+#define GET_DMA_POLARITY(chan) (DMAReq##chan##_ActiveLow | DMAAck##chan##_ActiveLow | EOT##chan##_ActiveLow)
+
+#elif defined(CONFIG_STBXXX_DMA) /* stb03xxx */
+
+#define DMA_PPC4xx_SIZE 4096
+
+/*
+ * DMA Status Register
+ */
+
+#define SET_DMA_PRIORITY(x) (((x)&0x00800001)) /* DMA Channel Priority */
+#define DMA_PRIORITY_MASK 0x00800001
+#define PRIORITY_LOW 0x00000000
+#define PRIORITY_MID_LOW 0x00000001
+#define PRIORITY_MID_HIGH 0x00800000
+#define PRIORITY_HIGH 0x00800001
+#define GET_DMA_PRIORITY(x) (((((x)&DMA_PRIORITY_MASK) &0x00800000) >> 22 ) | (((x)&DMA_PRIORITY_MASK) &0x00000001))
+
+#define DMA_CS0 (1<<31) /* Terminal Count has been reached */
+#define DMA_CS1 (1<<30)
+#define DMA_CS2 (1<<29)
+#define DMA_CS3 (1<<28)
+
+#define DMA_TS0 (1<<27) /* End of Transfer has been requested */
+#define DMA_TS1 (1<<26)
+#define DMA_TS2 (1<<25)
+#define DMA_TS3 (1<<24)
+
+#define DMA_CH0_ERR (1<<23) /* DMA Chanel 0 Error */
+#define DMA_CH1_ERR (1<<22)
+#define DMA_CH2_ERR (1<<21)
+#define DMA_CH3_ERR (1<<20)
+
+#define DMA_CT0 (1<<19) /* Chained transfere */
+
+#define DMA_IN_DMA_REQ0 (1<<18) /* Internal DMA Request is pending */
+#define DMA_IN_DMA_REQ1 (1<<17)
+#define DMA_IN_DMA_REQ2 (1<<16)
+#define DMA_IN_DMA_REQ3 (1<<15)
+
+#define DMA_EXT_DMA_REQ0 (1<<14) /* External DMA Request is pending */
+#define DMA_EXT_DMA_REQ1 (1<<13)
+#define DMA_EXT_DMA_REQ2 (1<<12)
+#define DMA_EXT_DMA_REQ3 (1<<11)
+
+#define DMA_CH0_BUSY (1<<10) /* DMA Channel 0 Busy */
+#define DMA_CH1_BUSY (1<<9)
+#define DMA_CH2_BUSY (1<<8)
+#define DMA_CH3_BUSY (1<<7)
+
+#define DMA_CT1 (1<<6) /* Chained transfere */
+#define DMA_CT2 (1<<5)
+#define DMA_CT3 (1<<4)
+
+#define DMA_CH_ENABLE (1<<7)
+#define SET_DMA_CH(x) (((x)&0x1)<<7)
+#define GET_DMA_CH(x) (((x)&DMA_CH_ENABLE)>>7)
+
+/* STBx25xxx dma unique */
+/* enable device port on a dma channel
+ * example ext 0 on dma 1
+ */
+
+#define SSP0_RECV 15
+#define SSP0_XMIT 14
+#define EXT_DMA_0 12
+#define SC1_XMIT 11
+#define SC1_RECV 10
+#define EXT_DMA_2 9
+#define EXT_DMA_3 8
+#define SERIAL2_XMIT 7
+#define SERIAL2_RECV 6
+#define SC0_XMIT 5
+#define SC0_RECV 4
+#define SERIAL1_XMIT 3
+#define SERIAL1_RECV 2
+#define SERIAL0_XMIT 1
+#define SERIAL0_RECV 0
+
+#define DMA_CHAN_0 1
+#define DMA_CHAN_1 2
+#define DMA_CHAN_2 3
+#define DMA_CHAN_3 4
+
+/* end STBx25xx */
+
+/*
+ * Bit 30 must be one for Redwoods, otherwise transfers may receive errors.
+ */
+#define DMA_CR_MB0 0x2
+
+#define SET_DMA_CONTROL \
+ (SET_DMA_CIE_ENABLE(p_init->int_enable) | /* interrupt enable */ \
+ SET_DMA_ETD(p_init->etd_output) | /* end of transfer pin */ \
+ SET_DMA_TCE(p_init->tce_enable) | /* terminal count enable */ \
+ SET_DMA_PL(p_init->pl) | /* peripheral location */ \
+ SET_DMA_DAI(p_init->dai) | /* dest addr increment */ \
+ SET_DMA_SAI(p_init->sai) | /* src addr increment */ \
+ SET_DMA_PRIORITY(p_init->cp) | /* channel priority */ \
+ SET_DMA_PW(p_init->pwidth) | /* peripheral/bus width */ \
+ SET_DMA_PSC(p_init->psc) | /* peripheral setup cycles */ \
+ SET_DMA_PWC(p_init->pwc) | /* peripheral wait cycles */ \
+ SET_DMA_PHC(p_init->phc) | /* peripheral hold cycles */ \
+ SET_DMA_TCD(p_init->tcd_disable) | /* TC chain mode disable */ \
+ SET_DMA_ECE(p_init->ece_enable) | /* ECE chanin mode enable */ \
+ SET_DMA_CH(p_init->ch_enable) | /* Chain enable */ \
+ DMA_CR_MB0 /* must be one */)
+
+#define GET_DMA_POLARITY(chan) chan
+
+#endif
+
+typedef struct {
+ unsigned short in_use; /* set when channel is being used, clr when
+ * available.
+ */
+ /*
+ * Valid polarity settings:
+ * DMAReq0_ActiveLow
+ * DMAAck0_ActiveLow
+ * EOT0_ActiveLow
+ *
+ * DMAReq1_ActiveLow
+ * DMAAck1_ActiveLow
+ * EOT1_ActiveLow
+ *
+ * DMAReq2_ActiveLow
+ * DMAAck2_ActiveLow
+ * EOT2_ActiveLow
+ *
+ * DMAReq3_ActiveLow
+ * DMAAck3_ActiveLow
+ * EOT3_ActiveLow
+ */
+ unsigned int polarity;
+
+ char buffer_enable; /* Boolean: buffer enable */
+ char tce_enable; /* Boolean: terminal count enable */
+ char etd_output; /* Boolean: eot pin is a tc output */
+ char pce; /* Boolean: parity check enable */
+
+ /*
+ * Peripheral location:
+ * INTERNAL_PERIPHERAL (UART0 on the 405GP)
+ * EXTERNAL_PERIPHERAL
+ */
+ char pl; /* internal/external peripheral */
+
+ /*
+ * Valid pwidth settings:
+ * PW_8
+ * PW_16
+ * PW_32
+ * PW_64
+ */
+ unsigned int pwidth;
+
+ char dai; /* Boolean: dst address increment */
+ char sai; /* Boolean: src address increment */
+
+ /*
+ * Valid psc settings: 0-3
+ */
+ unsigned int psc; /* Peripheral Setup Cycles */
+
+ /*
+ * Valid pwc settings:
+ * 0-63
+ */
+ unsigned int pwc; /* Peripheral Wait Cycles */
+
+ /*
+ * Valid phc settings:
+ * 0-7
+ */
+ unsigned int phc; /* Peripheral Hold Cycles */
+
+ /*
+ * Valid cp (channel priority) settings:
+ * PRIORITY_LOW
+ * PRIORITY_MID_LOW
+ * PRIORITY_MID_HIGH
+ * PRIORITY_HIGH
+ */
+ unsigned int cp; /* channel priority */
+
+ /*
+ * Valid pf (memory read prefetch) settings:
+ *
+ * PREFETCH_1
+ * PREFETCH_2
+ * PREFETCH_4
+ */
+ unsigned int pf; /* memory read prefetch */
+
+ /*
+ * Boolean: channel interrupt enable
+ * NOTE: for sgl transfers, only the last descriptor will be setup to
+ * interrupt.
+ */
+ char int_enable;
+
+ char shift; /* easy access to byte_count shift, based on */
+ /* the width of the channel */
+
+ uint32_t control; /* channel control word */
+
+ /* These variabled are used ONLY in single dma transfers */
+ unsigned int mode; /* transfer mode */
+ phys_addr_t addr;
+ char ce; /* channel enable */
+#ifdef CONFIG_STB03xxx
+ char ch_enable;
+ char tcd_disable;
+ char ece_enable;
+ char td; /* transfer direction */
+#endif
+
+} ppc_dma_ch_t;
+
+/*
+ * PPC44x DMA implementations have a slightly different
+ * descriptor layout. Probably moved about due to the
+ * change to 64-bit addresses and link pointer. I don't
+ * know why they didn't just leave control_count after
+ * the dst_addr.
+ */
+#ifdef PPC4xx_DMA_64BIT
+typedef struct {
+ uint32_t control;
+ uint32_t control_count;
+ phys_addr_t src_addr;
+ phys_addr_t dst_addr;
+ phys_addr_t next;
+} ppc_sgl_t;
+#else
+typedef struct {
+ uint32_t control;
+ phys_addr_t src_addr;
+ phys_addr_t dst_addr;
+ uint32_t control_count;
+ uint32_t next;
+} ppc_sgl_t;
+#endif
+
+typedef struct {
+ unsigned int dmanr;
+ uint32_t control; /* channel ctrl word; loaded from each descrptr */
+ uint32_t sgl_control; /* LK, TCI, ETI, and ERI bits in sgl descriptor */
+ dma_addr_t dma_addr; /* dma (physical) address of this list */
+ ppc_sgl_t *phead;
+ ppc_sgl_t *ptail;
+ uint32_t pad32[2];
+
+} sgl_list_info_t;
+
+typedef struct {
+ phys_addr_t *src_addr;
+ phys_addr_t *dst_addr;
+ phys_addr_t dma_src_addr;
+ phys_addr_t dma_dst_addr;
+} pci_alloc_desc_t;
+
+extern ppc_dma_ch_t dma_channels[];
+
+/*
+ * The DMA API are in ppc4xx_dma.c and ppc4xx_sgdma.c
+ */
+extern int ppc4xx_init_dma_channel(unsigned int, ppc_dma_ch_t *);
+extern int ppc4xx_get_channel_config(unsigned int, ppc_dma_ch_t *);
+extern int ppc4xx_set_channel_priority(unsigned int, unsigned int);
+extern unsigned int ppc4xx_get_peripheral_width(unsigned int);
+extern int ppc4xx_alloc_dma_handle(sgl_handle_t *, unsigned int, unsigned int);
+extern void ppc4xx_free_dma_handle(sgl_handle_t);
+extern int ppc4xx_get_dma_status(void);
+extern void ppc4xx_set_src_addr(int dmanr, phys_addr_t src_addr);
+extern void ppc4xx_set_dst_addr(int dmanr, phys_addr_t dst_addr);
+extern void ppc4xx_enable_dma(unsigned int dmanr);
+extern void ppc4xx_disable_dma(unsigned int dmanr);
+extern void ppc4xx_set_dma_count(unsigned int dmanr, unsigned int count);
+extern int ppc4xx_get_dma_residue(unsigned int dmanr);
+extern void ppc4xx_set_dma_addr2(unsigned int dmanr, phys_addr_t src_dma_addr,
+ phys_addr_t dst_dma_addr);
+extern int ppc4xx_enable_dma_interrupt(unsigned int dmanr);
+extern int ppc4xx_disable_dma_interrupt(unsigned int dmanr);
+extern int ppc4xx_clr_dma_status(unsigned int dmanr);
+extern int ppc4xx_map_dma_port(unsigned int dmanr, unsigned int ocp_dma,short dma_chan);
+extern int ppc4xx_disable_dma_port(unsigned int dmanr, unsigned int ocp_dma,short dma_chan);
+extern int ppc4xx_set_dma_mode(unsigned int dmanr, unsigned int mode);
+
+/* These are in kernel/dma.c: */
+
+/* reserve a DMA channel */
+extern int request_dma(unsigned int dmanr, const char *device_id);
+/* release it again */
+extern void free_dma(unsigned int dmanr);
+#endif
+#endif /* __KERNEL__ */
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)