patch-2.4.26 linux-2.4.26/include/asm-ppc/cpm2.h
Next file: linux-2.4.26/include/asm-ppc/cpm_8260.h
Previous file: linux-2.4.26/include/asm-m68k/keyboard.h
Back to the patch index
Back to the overall index
- Lines: 1038
- Date:
2004-04-14 06:05:40.000000000 -0700
- Orig file:
linux-2.4.25/include/asm-ppc/cpm2.h
- Orig date:
1969-12-31 16:00:00.000000000 -0800
diff -urN linux-2.4.25/include/asm-ppc/cpm2.h linux-2.4.26/include/asm-ppc/cpm2.h
@@ -0,0 +1,1037 @@
+/*
+ * Communication Processor Module v2.
+ *
+ * This file contains structures and information for the communication
+ * processor channels found in the dual port RAM or parameter RAM.
+ * All CPM control and status is available through the CPM2 internal
+ * memory map. See immap_cpm2.h for details.
+ */
+#ifdef __KERNEL__
+#ifndef __CPM2__
+#define __CPM2__
+
+#include <asm/immap_cpm2.h>
+
+/* CPM Command register.
+*/
+#define CPM_CR_RST ((uint)0x80000000)
+#define CPM_CR_PAGE ((uint)0x7c000000)
+#define CPM_CR_SBLOCK ((uint)0x03e00000)
+#define CPM_CR_FLG ((uint)0x00010000)
+#define CPM_CR_MCN ((uint)0x00003fc0)
+#define CPM_CR_OPCODE ((uint)0x0000000f)
+
+/* Device sub-block and page codes.
+*/
+#define CPM_CR_SCC1_SBLOCK (0x04)
+#define CPM_CR_SCC2_SBLOCK (0x05)
+#define CPM_CR_SCC3_SBLOCK (0x06)
+#define CPM_CR_SCC4_SBLOCK (0x07)
+#define CPM_CR_SMC1_SBLOCK (0x08)
+#define CPM_CR_SMC2_SBLOCK (0x09)
+#define CPM_CR_SPI_SBLOCK (0x0a)
+#define CPM_CR_I2C_SBLOCK (0x0b)
+#define CPM_CR_TIMER_SBLOCK (0x0f)
+#define CPM_CR_RAND_SBLOCK (0x0e)
+#define CPM_CR_FCC1_SBLOCK (0x10)
+#define CPM_CR_FCC2_SBLOCK (0x11)
+#define CPM_CR_FCC3_SBLOCK (0x12)
+#define CPM_CR_IDMA1_SBLOCK (0x14)
+#define CPM_CR_IDMA2_SBLOCK (0x15)
+#define CPM_CR_IDMA3_SBLOCK (0x16)
+#define CPM_CR_IDMA4_SBLOCK (0x17)
+#define CPM_CR_MCC1_SBLOCK (0x1c)
+
+#define CPM_CR_SCC1_PAGE (0x00)
+#define CPM_CR_SCC2_PAGE (0x01)
+#define CPM_CR_SCC3_PAGE (0x02)
+#define CPM_CR_SCC4_PAGE (0x03)
+#define CPM_CR_SMC1_PAGE (0x07)
+#define CPM_CR_SMC2_PAGE (0x08)
+#define CPM_CR_SPI_PAGE (0x09)
+#define CPM_CR_I2C_PAGE (0x0a)
+#define CPM_CR_TIMER_PAGE (0x0a)
+#define CPM_CR_RAND_PAGE (0x0a)
+#define CPM_CR_FCC1_PAGE (0x04)
+#define CPM_CR_FCC2_PAGE (0x05)
+#define CPM_CR_FCC3_PAGE (0x06)
+#define CPM_CR_IDMA1_PAGE (0x07)
+#define CPM_CR_IDMA2_PAGE (0x08)
+#define CPM_CR_IDMA3_PAGE (0x09)
+#define CPM_CR_IDMA4_PAGE (0x0a)
+#define CPM_CR_MCC1_PAGE (0x07)
+#define CPM_CR_MCC2_PAGE (0x08)
+
+/* Some opcodes (there are more...later)
+*/
+#define CPM_CR_INIT_TRX ((ushort)0x0000)
+#define CPM_CR_INIT_RX ((ushort)0x0001)
+#define CPM_CR_INIT_TX ((ushort)0x0002)
+#define CPM_CR_HUNT_MODE ((ushort)0x0003)
+#define CPM_CR_STOP_TX ((ushort)0x0004)
+#define CPM_CR_RESTART_TX ((ushort)0x0006)
+#define CPM_CR_SET_GADDR ((ushort)0x0008)
+#define CPM_CR_START_IDMA ((ushort)0x0009)
+#define CPM_CR_STOP_IDMA ((ushort)0x000b)
+
+#define mk_cr_cmd(PG, SBC, MCN, OP) \
+ ((PG << 26) | (SBC << 21) | (MCN << 6) | OP)
+
+/* Dual Port RAM addresses. The first 16K is available for almost
+ * any CPM use, so we put the BDs there. The first 128 bytes are
+ * used for SMC1 and SMC2 parameter RAM, so we start allocating
+ * BDs above that. All of this must change when we start
+ * downloading RAM microcode.
+ */
+#define CPM_DATAONLY_BASE ((uint)128)
+#define CPM_DP_NOSPACE ((uint)0x7fffffff)
+#ifdef CONFIG_8272
+#define CPM_DATAONLY_SIZE ((uint)(8 * 1024) - CPM_DATAONLY_BASE)
+#define CPM_FCC_SPECIAL_BASE ((uint)0x00009000)
+#else
+#define CPM_DATAONLY_SIZE ((uint)(16 * 1024) - CPM_DATAONLY_BASE)
+#define CPM_FCC_SPECIAL_BASE ((uint)0x0000b000)
+#endif
+
+/* The number of pages of host memory we allocate for CPM. This is
+ * done early in kernel initialization to get physically contiguous
+ * pages.
+ */
+#define NUM_CPM_HOST_PAGES 2
+
+
+/* Export the base address of the communication processor registers
+ * and dual port ram.
+ */
+extern cpm_cpm2_t *cpmp; /* Pointer to comm processor */
+uint cpm2_dpalloc(uint size, uint align);
+uint cpm2_hostalloc(uint size, uint align);
+void cpm2_setbrg(uint brg, uint rate);
+void cpm2_fastbrg(uint brg, uint rate, int div16);
+
+/* Buffer descriptors used by many of the CPM protocols.
+*/
+typedef struct cpm_buf_desc {
+ ushort cbd_sc; /* Status and Control */
+ ushort cbd_datlen; /* Data length in buffer */
+ uint cbd_bufaddr; /* Buffer address in host memory */
+} cbd_t;
+
+#define BD_SC_EMPTY ((ushort)0x8000) /* Receive is empty */
+#define BD_SC_READY ((ushort)0x8000) /* Transmit is ready */
+#define BD_SC_WRAP ((ushort)0x2000) /* Last buffer descriptor */
+#define BD_SC_INTRPT ((ushort)0x1000) /* Interrupt on change */
+#define BD_SC_LAST ((ushort)0x0800) /* Last buffer in frame */
+#define BD_SC_CM ((ushort)0x0200) /* Continous mode */
+#define BD_SC_ID ((ushort)0x0100) /* Rec'd too many idles */
+#define BD_SC_P ((ushort)0x0100) /* xmt preamble */
+#define BD_SC_BR ((ushort)0x0020) /* Break received */
+#define BD_SC_FR ((ushort)0x0010) /* Framing error */
+#define BD_SC_PR ((ushort)0x0008) /* Parity error */
+#define BD_SC_OV ((ushort)0x0002) /* Overrun */
+#define BD_SC_CD ((ushort)0x0001) /* ?? */
+
+/* Function code bits, usually generic to devices.
+*/
+#define CPMFCR_GBL ((u_char)0x20) /* Set memory snooping */
+#define CPMFCR_EB ((u_char)0x10) /* Set big endian byte order */
+#define CPMFCR_TC2 ((u_char)0x04) /* Transfer code 2 value */
+#define CPMFCR_DTB ((u_char)0x02) /* Use local bus for data when set */
+#define CPMFCR_BDB ((u_char)0x01) /* Use local bus for BD when set */
+
+/* Parameter RAM offsets from the base.
+*/
+#define PROFF_SCC1 ((uint)0x8000)
+#define PROFF_SCC2 ((uint)0x8100)
+#define PROFF_SCC3 ((uint)0x8200)
+#define PROFF_SCC4 ((uint)0x8300)
+#define PROFF_FCC1 ((uint)0x8400)
+#define PROFF_FCC2 ((uint)0x8500)
+#define PROFF_FCC3 ((uint)0x8600)
+#define PROFF_MCC1 ((uint)0x8700)
+#define PROFF_SMC1_BASE ((uint)0x87fc)
+#define PROFF_IDMA1_BASE ((uint)0x87fe)
+#define PROFF_MCC2 ((uint)0x8800)
+#define PROFF_SMC2_BASE ((uint)0x88fc)
+#define PROFF_IDMA2_BASE ((uint)0x88fe)
+#define PROFF_SPI_BASE ((uint)0x89fc)
+#define PROFF_IDMA3_BASE ((uint)0x89fe)
+#define PROFF_TIMERS ((uint)0x8ae0)
+#define PROFF_REVNUM ((uint)0x8af0)
+#define PROFF_RAND ((uint)0x8af8)
+#define PROFF_I2C_BASE ((uint)0x8afc)
+#define PROFF_IDMA4_BASE ((uint)0x8afe)
+
+/* The SMCs are relocated to any of the first eight DPRAM pages.
+ * We will fix these at the first locations of DPRAM, until we
+ * get some microcode patches :-).
+ * The parameter ram space for the SMCs is fifty-some bytes, and
+ * they are required to start on a 64 byte boundary.
+ */
+#define PROFF_SMC1 (0)
+#define PROFF_SMC2 (64)
+
+
+/* Define enough so I can at least use the serial port as a UART.
+ */
+typedef struct smc_uart {
+ ushort smc_rbase; /* Rx Buffer descriptor base address */
+ ushort smc_tbase; /* Tx Buffer descriptor base address */
+ u_char smc_rfcr; /* Rx function code */
+ u_char smc_tfcr; /* Tx function code */
+ ushort smc_mrblr; /* Max receive buffer length */
+ uint smc_rstate; /* Internal */
+ uint smc_idp; /* Internal */
+ ushort smc_rbptr; /* Internal */
+ ushort smc_ibc; /* Internal */
+ uint smc_rxtmp; /* Internal */
+ uint smc_tstate; /* Internal */
+ uint smc_tdp; /* Internal */
+ ushort smc_tbptr; /* Internal */
+ ushort smc_tbc; /* Internal */
+ uint smc_txtmp; /* Internal */
+ ushort smc_maxidl; /* Maximum idle characters */
+ ushort smc_tmpidl; /* Temporary idle counter */
+ ushort smc_brklen; /* Last received break length */
+ ushort smc_brkec; /* rcv'd break condition counter */
+ ushort smc_brkcr; /* xmt break count register */
+ ushort smc_rmask; /* Temporary bit mask */
+ uint smc_stmp; /* SDMA Temp */
+} smc_uart_t;
+
+/* SMC uart mode register (Internal memory map).
+*/
+#define SMCMR_REN ((ushort)0x0001)
+#define SMCMR_TEN ((ushort)0x0002)
+#define SMCMR_DM ((ushort)0x000c)
+#define SMCMR_SM_GCI ((ushort)0x0000)
+#define SMCMR_SM_UART ((ushort)0x0020)
+#define SMCMR_SM_TRANS ((ushort)0x0030)
+#define SMCMR_SM_MASK ((ushort)0x0030)
+#define SMCMR_PM_EVEN ((ushort)0x0100) /* Even parity, else odd */
+#define SMCMR_REVD SMCMR_PM_EVEN
+#define SMCMR_PEN ((ushort)0x0200) /* Parity enable */
+#define SMCMR_BS SMCMR_PEN
+#define SMCMR_SL ((ushort)0x0400) /* Two stops, else one */
+#define SMCR_CLEN_MASK ((ushort)0x7800) /* Character length */
+#define smcr_mk_clen(C) (((C) << 11) & SMCR_CLEN_MASK)
+
+/* SMC Event and Mask register.
+*/
+#define SMCM_BRKE ((unsigned char)0x40) /* When in UART Mode */
+#define SMCM_BRK ((unsigned char)0x10) /* When in UART Mode */
+#define SMCM_TXE ((unsigned char)0x10)
+#define SMCM_BSY ((unsigned char)0x04)
+#define SMCM_TX ((unsigned char)0x02)
+#define SMCM_RX ((unsigned char)0x01)
+
+/* Baud rate generators.
+*/
+#define CPM_BRG_RST ((uint)0x00020000)
+#define CPM_BRG_EN ((uint)0x00010000)
+#define CPM_BRG_EXTC_INT ((uint)0x00000000)
+#define CPM_BRG_EXTC_CLK3_9 ((uint)0x00004000)
+#define CPM_BRG_EXTC_CLK5_15 ((uint)0x00008000)
+#define CPM_BRG_ATB ((uint)0x00002000)
+#define CPM_BRG_CD_MASK ((uint)0x00001ffe)
+#define CPM_BRG_DIV16 ((uint)0x00000001)
+
+/* SCCs.
+*/
+#define SCC_GSMRH_IRP ((uint)0x00040000)
+#define SCC_GSMRH_GDE ((uint)0x00010000)
+#define SCC_GSMRH_TCRC_CCITT ((uint)0x00008000)
+#define SCC_GSMRH_TCRC_BISYNC ((uint)0x00004000)
+#define SCC_GSMRH_TCRC_HDLC ((uint)0x00000000)
+#define SCC_GSMRH_REVD ((uint)0x00002000)
+#define SCC_GSMRH_TRX ((uint)0x00001000)
+#define SCC_GSMRH_TTX ((uint)0x00000800)
+#define SCC_GSMRH_CDP ((uint)0x00000400)
+#define SCC_GSMRH_CTSP ((uint)0x00000200)
+#define SCC_GSMRH_CDS ((uint)0x00000100)
+#define SCC_GSMRH_CTSS ((uint)0x00000080)
+#define SCC_GSMRH_TFL ((uint)0x00000040)
+#define SCC_GSMRH_RFW ((uint)0x00000020)
+#define SCC_GSMRH_TXSY ((uint)0x00000010)
+#define SCC_GSMRH_SYNL16 ((uint)0x0000000c)
+#define SCC_GSMRH_SYNL8 ((uint)0x00000008)
+#define SCC_GSMRH_SYNL4 ((uint)0x00000004)
+#define SCC_GSMRH_RTSM ((uint)0x00000002)
+#define SCC_GSMRH_RSYN ((uint)0x00000001)
+
+#define SCC_GSMRL_SIR ((uint)0x80000000) /* SCC2 only */
+#define SCC_GSMRL_EDGE_NONE ((uint)0x60000000)
+#define SCC_GSMRL_EDGE_NEG ((uint)0x40000000)
+#define SCC_GSMRL_EDGE_POS ((uint)0x20000000)
+#define SCC_GSMRL_EDGE_BOTH ((uint)0x00000000)
+#define SCC_GSMRL_TCI ((uint)0x10000000)
+#define SCC_GSMRL_TSNC_3 ((uint)0x0c000000)
+#define SCC_GSMRL_TSNC_4 ((uint)0x08000000)
+#define SCC_GSMRL_TSNC_14 ((uint)0x04000000)
+#define SCC_GSMRL_TSNC_INF ((uint)0x00000000)
+#define SCC_GSMRL_RINV ((uint)0x02000000)
+#define SCC_GSMRL_TINV ((uint)0x01000000)
+#define SCC_GSMRL_TPL_128 ((uint)0x00c00000)
+#define SCC_GSMRL_TPL_64 ((uint)0x00a00000)
+#define SCC_GSMRL_TPL_48 ((uint)0x00800000)
+#define SCC_GSMRL_TPL_32 ((uint)0x00600000)
+#define SCC_GSMRL_TPL_16 ((uint)0x00400000)
+#define SCC_GSMRL_TPL_8 ((uint)0x00200000)
+#define SCC_GSMRL_TPL_NONE ((uint)0x00000000)
+#define SCC_GSMRL_TPP_ALL1 ((uint)0x00180000)
+#define SCC_GSMRL_TPP_01 ((uint)0x00100000)
+#define SCC_GSMRL_TPP_10 ((uint)0x00080000)
+#define SCC_GSMRL_TPP_ZEROS ((uint)0x00000000)
+#define SCC_GSMRL_TEND ((uint)0x00040000)
+#define SCC_GSMRL_TDCR_32 ((uint)0x00030000)
+#define SCC_GSMRL_TDCR_16 ((uint)0x00020000)
+#define SCC_GSMRL_TDCR_8 ((uint)0x00010000)
+#define SCC_GSMRL_TDCR_1 ((uint)0x00000000)
+#define SCC_GSMRL_RDCR_32 ((uint)0x0000c000)
+#define SCC_GSMRL_RDCR_16 ((uint)0x00008000)
+#define SCC_GSMRL_RDCR_8 ((uint)0x00004000)
+#define SCC_GSMRL_RDCR_1 ((uint)0x00000000)
+#define SCC_GSMRL_RENC_DFMAN ((uint)0x00003000)
+#define SCC_GSMRL_RENC_MANCH ((uint)0x00002000)
+#define SCC_GSMRL_RENC_FM0 ((uint)0x00001000)
+#define SCC_GSMRL_RENC_NRZI ((uint)0x00000800)
+#define SCC_GSMRL_RENC_NRZ ((uint)0x00000000)
+#define SCC_GSMRL_TENC_DFMAN ((uint)0x00000600)
+#define SCC_GSMRL_TENC_MANCH ((uint)0x00000400)
+#define SCC_GSMRL_TENC_FM0 ((uint)0x00000200)
+#define SCC_GSMRL_TENC_NRZI ((uint)0x00000100)
+#define SCC_GSMRL_TENC_NRZ ((uint)0x00000000)
+#define SCC_GSMRL_DIAG_LE ((uint)0x000000c0) /* Loop and echo */
+#define SCC_GSMRL_DIAG_ECHO ((uint)0x00000080)
+#define SCC_GSMRL_DIAG_LOOP ((uint)0x00000040)
+#define SCC_GSMRL_DIAG_NORM ((uint)0x00000000)
+#define SCC_GSMRL_ENR ((uint)0x00000020)
+#define SCC_GSMRL_ENT ((uint)0x00000010)
+#define SCC_GSMRL_MODE_ENET ((uint)0x0000000c)
+#define SCC_GSMRL_MODE_DDCMP ((uint)0x00000009)
+#define SCC_GSMRL_MODE_BISYNC ((uint)0x00000008)
+#define SCC_GSMRL_MODE_V14 ((uint)0x00000007)
+#define SCC_GSMRL_MODE_AHDLC ((uint)0x00000006)
+#define SCC_GSMRL_MODE_PROFIBUS ((uint)0x00000005)
+#define SCC_GSMRL_MODE_UART ((uint)0x00000004)
+#define SCC_GSMRL_MODE_SS7 ((uint)0x00000003)
+#define SCC_GSMRL_MODE_ATALK ((uint)0x00000002)
+#define SCC_GSMRL_MODE_HDLC ((uint)0x00000000)
+
+#define SCC_TODR_TOD ((ushort)0x8000)
+
+/* SCC Event and Mask register.
+*/
+#define SCCM_TXE ((unsigned char)0x10)
+#define SCCM_BSY ((unsigned char)0x04)
+#define SCCM_TX ((unsigned char)0x02)
+#define SCCM_RX ((unsigned char)0x01)
+
+typedef struct scc_param {
+ ushort scc_rbase; /* Rx Buffer descriptor base address */
+ ushort scc_tbase; /* Tx Buffer descriptor base address */
+ u_char scc_rfcr; /* Rx function code */
+ u_char scc_tfcr; /* Tx function code */
+ ushort scc_mrblr; /* Max receive buffer length */
+ uint scc_rstate; /* Internal */
+ uint scc_idp; /* Internal */
+ ushort scc_rbptr; /* Internal */
+ ushort scc_ibc; /* Internal */
+ uint scc_rxtmp; /* Internal */
+ uint scc_tstate; /* Internal */
+ uint scc_tdp; /* Internal */
+ ushort scc_tbptr; /* Internal */
+ ushort scc_tbc; /* Internal */
+ uint scc_txtmp; /* Internal */
+ uint scc_rcrc; /* Internal */
+ uint scc_tcrc; /* Internal */
+} sccp_t;
+
+/* CPM Ethernet through SCC1.
+ */
+typedef struct scc_enet {
+ sccp_t sen_genscc;
+ uint sen_cpres; /* Preset CRC */
+ uint sen_cmask; /* Constant mask for CRC */
+ uint sen_crcec; /* CRC Error counter */
+ uint sen_alec; /* alignment error counter */
+ uint sen_disfc; /* discard frame counter */
+ ushort sen_pads; /* Tx short frame pad character */
+ ushort sen_retlim; /* Retry limit threshold */
+ ushort sen_retcnt; /* Retry limit counter */
+ ushort sen_maxflr; /* maximum frame length register */
+ ushort sen_minflr; /* minimum frame length register */
+ ushort sen_maxd1; /* maximum DMA1 length */
+ ushort sen_maxd2; /* maximum DMA2 length */
+ ushort sen_maxd; /* Rx max DMA */
+ ushort sen_dmacnt; /* Rx DMA counter */
+ ushort sen_maxb; /* Max BD byte count */
+ ushort sen_gaddr1; /* Group address filter */
+ ushort sen_gaddr2;
+ ushort sen_gaddr3;
+ ushort sen_gaddr4;
+ uint sen_tbuf0data0; /* Save area 0 - current frame */
+ uint sen_tbuf0data1; /* Save area 1 - current frame */
+ uint sen_tbuf0rba; /* Internal */
+ uint sen_tbuf0crc; /* Internal */
+ ushort sen_tbuf0bcnt; /* Internal */
+ ushort sen_paddrh; /* physical address (MSB) */
+ ushort sen_paddrm;
+ ushort sen_paddrl; /* physical address (LSB) */
+ ushort sen_pper; /* persistence */
+ ushort sen_rfbdptr; /* Rx first BD pointer */
+ ushort sen_tfbdptr; /* Tx first BD pointer */
+ ushort sen_tlbdptr; /* Tx last BD pointer */
+ uint sen_tbuf1data0; /* Save area 0 - current frame */
+ uint sen_tbuf1data1; /* Save area 1 - current frame */
+ uint sen_tbuf1rba; /* Internal */
+ uint sen_tbuf1crc; /* Internal */
+ ushort sen_tbuf1bcnt; /* Internal */
+ ushort sen_txlen; /* Tx Frame length counter */
+ ushort sen_iaddr1; /* Individual address filter */
+ ushort sen_iaddr2;
+ ushort sen_iaddr3;
+ ushort sen_iaddr4;
+ ushort sen_boffcnt; /* Backoff counter */
+
+ /* NOTE: Some versions of the manual have the following items
+ * incorrectly documented. Below is the proper order.
+ */
+ ushort sen_taddrh; /* temp address (MSB) */
+ ushort sen_taddrm;
+ ushort sen_taddrl; /* temp address (LSB) */
+} scc_enet_t;
+
+
+/* SCC Event register as used by Ethernet.
+*/
+#define SCCE_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */
+#define SCCE_ENET_TXE ((ushort)0x0010) /* Transmit Error */
+#define SCCE_ENET_RXF ((ushort)0x0008) /* Full frame received */
+#define SCCE_ENET_BSY ((ushort)0x0004) /* All incoming buffers full */
+#define SCCE_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */
+#define SCCE_ENET_RXB ((ushort)0x0001) /* A buffer was received */
+
+/* SCC Mode Register (PSMR) as used by Ethernet.
+*/
+#define SCC_PSMR_HBC ((ushort)0x8000) /* Enable heartbeat */
+#define SCC_PSMR_FC ((ushort)0x4000) /* Force collision */
+#define SCC_PSMR_RSH ((ushort)0x2000) /* Receive short frames */
+#define SCC_PSMR_IAM ((ushort)0x1000) /* Check individual hash */
+#define SCC_PSMR_ENCRC ((ushort)0x0800) /* Ethernet CRC mode */
+#define SCC_PSMR_PRO ((ushort)0x0200) /* Promiscuous mode */
+#define SCC_PSMR_BRO ((ushort)0x0100) /* Catch broadcast pkts */
+#define SCC_PSMR_SBT ((ushort)0x0080) /* Special backoff timer */
+#define SCC_PSMR_LPB ((ushort)0x0040) /* Set Loopback mode */
+#define SCC_PSMR_SIP ((ushort)0x0020) /* Sample Input Pins */
+#define SCC_PSMR_LCW ((ushort)0x0010) /* Late collision window */
+#define SCC_PSMR_NIB22 ((ushort)0x000a) /* Start frame search */
+#define SCC_PSMR_FDE ((ushort)0x0001) /* Full duplex enable */
+
+/* Buffer descriptor control/status used by Ethernet receive.
+ * Common to SCC and FCC.
+ */
+#define BD_ENET_RX_EMPTY ((ushort)0x8000)
+#define BD_ENET_RX_WRAP ((ushort)0x2000)
+#define BD_ENET_RX_INTR ((ushort)0x1000)
+#define BD_ENET_RX_LAST ((ushort)0x0800)
+#define BD_ENET_RX_FIRST ((ushort)0x0400)
+#define BD_ENET_RX_MISS ((ushort)0x0100)
+#define BD_ENET_RX_BC ((ushort)0x0080) /* FCC Only */
+#define BD_ENET_RX_MC ((ushort)0x0040) /* FCC Only */
+#define BD_ENET_RX_LG ((ushort)0x0020)
+#define BD_ENET_RX_NO ((ushort)0x0010)
+#define BD_ENET_RX_SH ((ushort)0x0008)
+#define BD_ENET_RX_CR ((ushort)0x0004)
+#define BD_ENET_RX_OV ((ushort)0x0002)
+#define BD_ENET_RX_CL ((ushort)0x0001)
+#define BD_ENET_RX_STATS ((ushort)0x01ff) /* All status bits */
+
+/* Buffer descriptor control/status used by Ethernet transmit.
+ * Common to SCC and FCC.
+ */
+#define BD_ENET_TX_READY ((ushort)0x8000)
+#define BD_ENET_TX_PAD ((ushort)0x4000)
+#define BD_ENET_TX_WRAP ((ushort)0x2000)
+#define BD_ENET_TX_INTR ((ushort)0x1000)
+#define BD_ENET_TX_LAST ((ushort)0x0800)
+#define BD_ENET_TX_TC ((ushort)0x0400)
+#define BD_ENET_TX_DEF ((ushort)0x0200)
+#define BD_ENET_TX_HB ((ushort)0x0100)
+#define BD_ENET_TX_LC ((ushort)0x0080)
+#define BD_ENET_TX_RL ((ushort)0x0040)
+#define BD_ENET_TX_RCMASK ((ushort)0x003c)
+#define BD_ENET_TX_UN ((ushort)0x0002)
+#define BD_ENET_TX_CSL ((ushort)0x0001)
+#define BD_ENET_TX_STATS ((ushort)0x03ff) /* All status bits */
+
+/* SCC as UART
+*/
+typedef struct scc_uart {
+ sccp_t scc_genscc;
+ uint scc_res1; /* Reserved */
+ uint scc_res2; /* Reserved */
+ ushort scc_maxidl; /* Maximum idle chars */
+ ushort scc_idlc; /* temp idle counter */
+ ushort scc_brkcr; /* Break count register */
+ ushort scc_parec; /* receive parity error counter */
+ ushort scc_frmec; /* receive framing error counter */
+ ushort scc_nosec; /* receive noise counter */
+ ushort scc_brkec; /* receive break condition counter */
+ ushort scc_brkln; /* last received break length */
+ ushort scc_uaddr1; /* UART address character 1 */
+ ushort scc_uaddr2; /* UART address character 2 */
+ ushort scc_rtemp; /* Temp storage */
+ ushort scc_toseq; /* Transmit out of sequence char */
+ ushort scc_char1; /* control character 1 */
+ ushort scc_char2; /* control character 2 */
+ ushort scc_char3; /* control character 3 */
+ ushort scc_char4; /* control character 4 */
+ ushort scc_char5; /* control character 5 */
+ ushort scc_char6; /* control character 6 */
+ ushort scc_char7; /* control character 7 */
+ ushort scc_char8; /* control character 8 */
+ ushort scc_rccm; /* receive control character mask */
+ ushort scc_rccr; /* receive control character register */
+ ushort scc_rlbc; /* receive last break character */
+} scc_uart_t;
+
+/* SCC Event and Mask registers when it is used as a UART.
+*/
+#define UART_SCCM_GLR ((ushort)0x1000)
+#define UART_SCCM_GLT ((ushort)0x0800)
+#define UART_SCCM_AB ((ushort)0x0200)
+#define UART_SCCM_IDL ((ushort)0x0100)
+#define UART_SCCM_GRA ((ushort)0x0080)
+#define UART_SCCM_BRKE ((ushort)0x0040)
+#define UART_SCCM_BRKS ((ushort)0x0020)
+#define UART_SCCM_CCR ((ushort)0x0008)
+#define UART_SCCM_BSY ((ushort)0x0004)
+#define UART_SCCM_TX ((ushort)0x0002)
+#define UART_SCCM_RX ((ushort)0x0001)
+
+/* The SCC PSMR when used as a UART.
+*/
+#define SCU_PSMR_FLC ((ushort)0x8000)
+#define SCU_PSMR_SL ((ushort)0x4000)
+#define SCU_PSMR_CL ((ushort)0x3000)
+#define SCU_PSMR_UM ((ushort)0x0c00)
+#define SCU_PSMR_FRZ ((ushort)0x0200)
+#define SCU_PSMR_RZS ((ushort)0x0100)
+#define SCU_PSMR_SYN ((ushort)0x0080)
+#define SCU_PSMR_DRT ((ushort)0x0040)
+#define SCU_PSMR_PEN ((ushort)0x0010)
+#define SCU_PSMR_RPM ((ushort)0x000c)
+#define SCU_PSMR_REVP ((ushort)0x0008)
+#define SCU_PSMR_TPM ((ushort)0x0003)
+#define SCU_PSMR_TEVP ((ushort)0x0003)
+
+/* CPM Transparent mode SCC.
+ */
+typedef struct scc_trans {
+ sccp_t st_genscc;
+ uint st_cpres; /* Preset CRC */
+ uint st_cmask; /* Constant mask for CRC */
+} scc_trans_t;
+
+#define BD_SCC_TX_LAST ((ushort)0x0800)
+
+/* How about some FCCs.....
+*/
+#define FCC_GFMR_DIAG_NORM ((uint)0x00000000)
+#define FCC_GFMR_DIAG_LE ((uint)0x40000000)
+#define FCC_GFMR_DIAG_AE ((uint)0x80000000)
+#define FCC_GFMR_DIAG_ALE ((uint)0xc0000000)
+#define FCC_GFMR_TCI ((uint)0x20000000)
+#define FCC_GFMR_TRX ((uint)0x10000000)
+#define FCC_GFMR_TTX ((uint)0x08000000)
+#define FCC_GFMR_TTX ((uint)0x08000000)
+#define FCC_GFMR_CDP ((uint)0x04000000)
+#define FCC_GFMR_CTSP ((uint)0x02000000)
+#define FCC_GFMR_CDS ((uint)0x01000000)
+#define FCC_GFMR_CTSS ((uint)0x00800000)
+#define FCC_GFMR_SYNL_NONE ((uint)0x00000000)
+#define FCC_GFMR_SYNL_AUTO ((uint)0x00004000)
+#define FCC_GFMR_SYNL_8 ((uint)0x00008000)
+#define FCC_GFMR_SYNL_16 ((uint)0x0000c000)
+#define FCC_GFMR_RTSM ((uint)0x00002000)
+#define FCC_GFMR_RENC_NRZ ((uint)0x00000000)
+#define FCC_GFMR_RENC_NRZI ((uint)0x00000800)
+#define FCC_GFMR_REVD ((uint)0x00000400)
+#define FCC_GFMR_TENC_NRZ ((uint)0x00000000)
+#define FCC_GFMR_TENC_NRZI ((uint)0x00000100)
+#define FCC_GFMR_TCRC_16 ((uint)0x00000000)
+#define FCC_GFMR_TCRC_32 ((uint)0x00000080)
+#define FCC_GFMR_ENR ((uint)0x00000020)
+#define FCC_GFMR_ENT ((uint)0x00000010)
+#define FCC_GFMR_MODE_ENET ((uint)0x0000000c)
+#define FCC_GFMR_MODE_ATM ((uint)0x0000000a)
+#define FCC_GFMR_MODE_HDLC ((uint)0x00000000)
+
+/* Generic FCC parameter ram.
+*/
+typedef struct fcc_param {
+ ushort fcc_riptr; /* Rx Internal temp pointer */
+ ushort fcc_tiptr; /* Tx Internal temp pointer */
+ ushort fcc_res1;
+ ushort fcc_mrblr; /* Max receive buffer length, mod 32 bytes */
+ uint fcc_rstate; /* Upper byte is Func code, must be set */
+ uint fcc_rbase; /* Receive BD base */
+ ushort fcc_rbdstat; /* RxBD status */
+ ushort fcc_rbdlen; /* RxBD down counter */
+ uint fcc_rdptr; /* RxBD internal data pointer */
+ uint fcc_tstate; /* Upper byte is Func code, must be set */
+ uint fcc_tbase; /* Transmit BD base */
+ ushort fcc_tbdstat; /* TxBD status */
+ ushort fcc_tbdlen; /* TxBD down counter */
+ uint fcc_tdptr; /* TxBD internal data pointer */
+ uint fcc_rbptr; /* Rx BD Internal buf pointer */
+ uint fcc_tbptr; /* Tx BD Internal buf pointer */
+ uint fcc_rcrc; /* Rx temp CRC */
+ uint fcc_res2;
+ uint fcc_tcrc; /* Tx temp CRC */
+} fccp_t;
+
+
+/* Ethernet controller through FCC.
+*/
+typedef struct fcc_enet {
+ fccp_t fen_genfcc;
+ uint fen_statbuf; /* Internal status buffer */
+ uint fen_camptr; /* CAM address */
+ uint fen_cmask; /* Constant mask for CRC */
+ uint fen_cpres; /* Preset CRC */
+ uint fen_crcec; /* CRC Error counter */
+ uint fen_alec; /* alignment error counter */
+ uint fen_disfc; /* discard frame counter */
+ ushort fen_retlim; /* Retry limit */
+ ushort fen_retcnt; /* Retry counter */
+ ushort fen_pper; /* Persistence */
+ ushort fen_boffcnt; /* backoff counter */
+ uint fen_gaddrh; /* Group address filter, high 32-bits */
+ uint fen_gaddrl; /* Group address filter, low 32-bits */
+ ushort fen_tfcstat; /* out of sequence TxBD */
+ ushort fen_tfclen;
+ uint fen_tfcptr;
+ ushort fen_mflr; /* Maximum frame length (1518) */
+ ushort fen_paddrh; /* MAC address */
+ ushort fen_paddrm;
+ ushort fen_paddrl;
+ ushort fen_ibdcount; /* Internal BD counter */
+ ushort fen_ibdstart; /* Internal BD start pointer */
+ ushort fen_ibdend; /* Internal BD end pointer */
+ ushort fen_txlen; /* Internal Tx frame length counter */
+ uint fen_ibdbase[8]; /* Internal use */
+ uint fen_iaddrh; /* Individual address filter */
+ uint fen_iaddrl;
+ ushort fen_minflr; /* Minimum frame length (64) */
+ ushort fen_taddrh; /* Filter transfer MAC address */
+ ushort fen_taddrm;
+ ushort fen_taddrl;
+ ushort fen_padptr; /* Pointer to pad byte buffer */
+ ushort fen_cftype; /* control frame type */
+ ushort fen_cfrange; /* control frame range */
+ ushort fen_maxb; /* maximum BD count */
+ ushort fen_maxd1; /* Max DMA1 length (1520) */
+ ushort fen_maxd2; /* Max DMA2 length (1520) */
+ ushort fen_maxd; /* internal max DMA count */
+ ushort fen_dmacnt; /* internal DMA counter */
+ uint fen_octc; /* Total octect counter */
+ uint fen_colc; /* Total collision counter */
+ uint fen_broc; /* Total broadcast packet counter */
+ uint fen_mulc; /* Total multicast packet count */
+ uint fen_uspc; /* Total packets < 64 bytes */
+ uint fen_frgc; /* Total packets < 64 bytes with errors */
+ uint fen_ospc; /* Total packets > 1518 */
+ uint fen_jbrc; /* Total packets > 1518 with errors */
+ uint fen_p64c; /* Total packets == 64 bytes */
+ uint fen_p65c; /* Total packets 64 < bytes <= 127 */
+ uint fen_p128c; /* Total packets 127 < bytes <= 255 */
+ uint fen_p256c; /* Total packets 256 < bytes <= 511 */
+ uint fen_p512c; /* Total packets 512 < bytes <= 1023 */
+ uint fen_p1024c; /* Total packets 1024 < bytes <= 1518 */
+ uint fen_cambuf; /* Internal CAM buffer poiner */
+ ushort fen_rfthr; /* Received frames threshold */
+ ushort fen_rfcnt; /* Received frames count */
+} fcc_enet_t;
+
+/* FCC Event/Mask register as used by Ethernet.
+*/
+#define FCC_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */
+#define FCC_ENET_RXC ((ushort)0x0040) /* Control Frame Received */
+#define FCC_ENET_TXC ((ushort)0x0020) /* Out of seq. Tx sent */
+#define FCC_ENET_TXE ((ushort)0x0010) /* Transmit Error */
+#define FCC_ENET_RXF ((ushort)0x0008) /* Full frame received */
+#define FCC_ENET_BSY ((ushort)0x0004) /* Busy. Rx Frame dropped */
+#define FCC_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */
+#define FCC_ENET_RXB ((ushort)0x0001) /* A buffer was received */
+
+/* FCC Mode Register (FPSMR) as used by Ethernet.
+*/
+#define FCC_PSMR_HBC ((uint)0x80000000) /* Enable heartbeat */
+#define FCC_PSMR_FC ((uint)0x40000000) /* Force Collision */
+#define FCC_PSMR_SBT ((uint)0x20000000) /* Stop backoff timer */
+#define FCC_PSMR_LPB ((uint)0x10000000) /* Local protect. 1 = FDX */
+#define FCC_PSMR_LCW ((uint)0x08000000) /* Late collision select */
+#define FCC_PSMR_FDE ((uint)0x04000000) /* Full Duplex Enable */
+#define FCC_PSMR_MON ((uint)0x02000000) /* RMON Enable */
+#define FCC_PSMR_PRO ((uint)0x00400000) /* Promiscuous Enable */
+#define FCC_PSMR_FCE ((uint)0x00200000) /* Flow Control Enable */
+#define FCC_PSMR_RSH ((uint)0x00100000) /* Receive Short Frames */
+#define FCC_PSMR_CAM ((uint)0x00000400) /* CAM enable */
+#define FCC_PSMR_BRO ((uint)0x00000200) /* Broadcast pkt discard */
+#define FCC_PSMR_ENCRC ((uint)0x00000080) /* Use 32-bit CRC */
+
+/* IIC parameter RAM.
+*/
+typedef struct iic {
+ ushort iic_rbase; /* Rx Buffer descriptor base address */
+ ushort iic_tbase; /* Tx Buffer descriptor base address */
+ u_char iic_rfcr; /* Rx function code */
+ u_char iic_tfcr; /* Tx function code */
+ ushort iic_mrblr; /* Max receive buffer length */
+ uint iic_rstate; /* Internal */
+ uint iic_rdp; /* Internal */
+ ushort iic_rbptr; /* Internal */
+ ushort iic_rbc; /* Internal */
+ uint iic_rxtmp; /* Internal */
+ uint iic_tstate; /* Internal */
+ uint iic_tdp; /* Internal */
+ ushort iic_tbptr; /* Internal */
+ ushort iic_tbc; /* Internal */
+ uint iic_txtmp; /* Internal */
+} iic_t;
+
+/* SPI parameter RAM.
+*/
+typedef struct spi {
+ ushort spi_rbase; /* Rx Buffer descriptor base address */
+ ushort spi_tbase; /* Tx Buffer descriptor base address */
+ u_char spi_rfcr; /* Rx function code */
+ u_char spi_tfcr; /* Tx function code */
+ ushort spi_mrblr; /* Max receive buffer length */
+ uint spi_rstate; /* Internal */
+ uint spi_rdp; /* Internal */
+ ushort spi_rbptr; /* Internal */
+ ushort spi_rbc; /* Internal */
+ uint spi_rxtmp; /* Internal */
+ uint spi_tstate; /* Internal */
+ uint spi_tdp; /* Internal */
+ ushort spi_tbptr; /* Internal */
+ ushort spi_tbc; /* Internal */
+ uint spi_txtmp; /* Internal */
+ uint spi_res; /* Tx temp. */
+ uint spi_res1[4]; /* SDMA temp. */
+} spi_t;
+
+/* SPI Mode register.
+*/
+#define SPMODE_LOOP ((ushort)0x4000) /* Loopback */
+#define SPMODE_CI ((ushort)0x2000) /* Clock Invert */
+#define SPMODE_CP ((ushort)0x1000) /* Clock Phase */
+#define SPMODE_DIV16 ((ushort)0x0800) /* BRG/16 mode */
+#define SPMODE_REV ((ushort)0x0400) /* Reversed Data */
+#define SPMODE_MSTR ((ushort)0x0200) /* SPI Master */
+#define SPMODE_EN ((ushort)0x0100) /* Enable */
+#define SPMODE_LENMSK ((ushort)0x00f0) /* character length */
+#define SPMODE_PMMSK ((ushort)0x000f) /* prescale modulus */
+
+#define SPMODE_LEN(x) ((((x)-1)&0xF)<<4)
+#define SPMODE_PM(x) ((x) &0xF)
+
+#define SPI_EB ((u_char)0x10) /* big endian byte order */
+
+#define BD_IIC_START ((ushort)0x0400)
+
+/* IDMA parameter RAM
+*/
+typedef struct idma {
+ ushort ibase; /* IDMA buffer descriptor table base address */
+ ushort dcm; /* DMA channel mode */
+ ushort ibdptr; /* IDMA current buffer descriptor pointer */
+ ushort dpr_buf; /* IDMA transfer buffer base address */
+ ushort buf_inv; /* internal buffer inventory */
+ ushort ss_max; /* steady-state maximum transfer size */
+ ushort dpr_in_ptr; /* write pointer inside the internal buffer */
+ ushort sts; /* source transfer size */
+ ushort dpr_out_ptr; /* read pointer inside the internal buffer */
+ ushort seob; /* source end of burst */
+ ushort deob; /* destination end of burst */
+ ushort dts; /* destination transfer size */
+ ushort ret_add; /* return address when working in ERM=1 mode */
+ ushort res0; /* reserved */
+ uint bd_cnt; /* internal byte count */
+ uint s_ptr; /* source internal data pointer */
+ uint d_ptr; /* destination internal data pointer */
+ uint istate; /* internal state */
+ u_char res1[20]; /* pad to 64-byte length */
+} idma_t;
+
+/* DMA channel mode bit fields
+*/
+#define IDMA_DCM_FB ((ushort)0x8000) /* fly-by mode */
+#define IDMA_DCM_LP ((ushort)0x4000) /* low priority */
+#define IDMA_DCM_TC2 ((ushort)0x0400) /* value driven on TC[2] */
+#define IDMA_DCM_DMA_WRAP_MASK ((ushort)0x01c0) /* mask for DMA wrap */
+#define IDMA_DCM_DMA_WRAP_64 ((ushort)0x0000) /* 64-byte DMA xfer buffer */
+#define IDMA_DCM_DMA_WRAP_128 ((ushort)0x0040) /* 128-byte DMA xfer buffer */
+#define IDMA_DCM_DMA_WRAP_256 ((ushort)0x0080) /* 256-byte DMA xfer buffer */
+#define IDMA_DCM_DMA_WRAP_512 ((ushort)0x00c0) /* 512-byte DMA xfer buffer */
+#define IDMA_DCM_DMA_WRAP_1024 ((ushort)0x0100) /* 1024-byte DMA xfer buffer */
+#define IDMA_DCM_DMA_WRAP_2048 ((ushort)0x0140) /* 2048-byte DMA xfer buffer */
+#define IDMA_DCM_SINC ((ushort)0x0020) /* source inc addr */
+#define IDMA_DCM_DINC ((ushort)0x0010) /* destination inc addr */
+#define IDMA_DCM_ERM ((ushort)0x0008) /* external request mode */
+#define IDMA_DCM_DT ((ushort)0x0004) /* DONE treatment */
+#define IDMA_DCM_SD_MASK ((ushort)0x0003) /* mask for SD bit field */
+#define IDMA_DCM_SD_MEM2MEM ((ushort)0x0000) /* memory-to-memory xfer */
+#define IDMA_DCM_SD_PER2MEM ((ushort)0x0002) /* peripheral-to-memory xfer */
+#define IDMA_DCM_SD_MEM2PER ((ushort)0x0001) /* memory-to-peripheral xfer */
+
+/* IDMA Buffer Descriptors
+*/
+typedef struct idma_bd {
+ uint flags;
+ uint len; /* data length */
+ uint src; /* source data buffer pointer */
+ uint dst; /* destination data buffer pointer */
+} idma_bd_t;
+
+/* IDMA buffer descriptor flag bit fields
+*/
+#define IDMA_BD_V ((uint)0x80000000) /* valid */
+#define IDMA_BD_W ((uint)0x20000000) /* wrap */
+#define IDMA_BD_I ((uint)0x10000000) /* interrupt */
+#define IDMA_BD_L ((uint)0x08000000) /* last */
+#define IDMA_BD_CM ((uint)0x02000000) /* continuous mode */
+#define IDMA_BD_SDN ((uint)0x00400000) /* source done */
+#define IDMA_BD_DDN ((uint)0x00200000) /* destination done */
+#define IDMA_BD_DGBL ((uint)0x00100000) /* destination global */
+#define IDMA_BD_DBO_LE ((uint)0x00040000) /* little-end dest byte order */
+#define IDMA_BD_DBO_BE ((uint)0x00080000) /* big-end dest byte order */
+#define IDMA_BD_DDTB ((uint)0x00010000) /* destination data bus */
+#define IDMA_BD_SGBL ((uint)0x00002000) /* source global */
+#define IDMA_BD_SBO_LE ((uint)0x00000800) /* little-end src byte order */
+#define IDMA_BD_SBO_BE ((uint)0x00001000) /* big-end src byte order */
+#define IDMA_BD_SDTB ((uint)0x00000200) /* source data bus */
+
+/* per-channel IDMA registers
+*/
+typedef struct im_idma {
+ u_char idsr; /* IDMAn event status register */
+ u_char res0[3];
+ u_char idmr; /* IDMAn event mask register */
+ u_char res1[3];
+} im_idma_t;
+
+/* IDMA event register bit fields
+*/
+#define IDMA_EVENT_SC ((unsigned char)0x08) /* stop completed */
+#define IDMA_EVENT_OB ((unsigned char)0x04) /* out of buffers */
+#define IDMA_EVENT_EDN ((unsigned char)0x02) /* external DONE asserted */
+#define IDMA_EVENT_BC ((unsigned char)0x01) /* buffer descriptor complete */
+
+/* RISC Controller Configuration Register (RCCR) bit fields
+*/
+#define RCCR_TIME ((uint)0x80000000) /* timer enable */
+#define RCCR_TIMEP_MASK ((uint)0x3f000000) /* mask for timer period bit field */
+#define RCCR_DR0M ((uint)0x00800000) /* IDMA0 request mode */
+#define RCCR_DR1M ((uint)0x00400000) /* IDMA1 request mode */
+#define RCCR_DR2M ((uint)0x00000080) /* IDMA2 request mode */
+#define RCCR_DR3M ((uint)0x00000040) /* IDMA3 request mode */
+#define RCCR_DR0QP_MASK ((uint)0x00300000) /* mask for IDMA0 req priority */
+#define RCCR_DR0QP_HIGH ((uint)0x00000000) /* IDMA0 has high req priority */
+#define RCCR_DR0QP_MED ((uint)0x00100000) /* IDMA0 has medium req priority */
+#define RCCR_DR0QP_LOW ((uint)0x00200000) /* IDMA0 has low req priority */
+#define RCCR_DR1QP_MASK ((uint)0x00030000) /* mask for IDMA1 req priority */
+#define RCCR_DR1QP_HIGH ((uint)0x00000000) /* IDMA1 has high req priority */
+#define RCCR_DR1QP_MED ((uint)0x00010000) /* IDMA1 has medium req priority */
+#define RCCR_DR1QP_LOW ((uint)0x00020000) /* IDMA1 has low req priority */
+#define RCCR_DR2QP_MASK ((uint)0x00000030) /* mask for IDMA2 req priority */
+#define RCCR_DR2QP_HIGH ((uint)0x00000000) /* IDMA2 has high req priority */
+#define RCCR_DR2QP_MED ((uint)0x00000010) /* IDMA2 has medium req priority */
+#define RCCR_DR2QP_LOW ((uint)0x00000020) /* IDMA2 has low req priority */
+#define RCCR_DR3QP_MASK ((uint)0x00000003) /* mask for IDMA3 req priority */
+#define RCCR_DR3QP_HIGH ((uint)0x00000000) /* IDMA3 has high req priority */
+#define RCCR_DR3QP_MED ((uint)0x00000001) /* IDMA3 has medium req priority */
+#define RCCR_DR3QP_LOW ((uint)0x00000002) /* IDMA3 has low req priority */
+#define RCCR_EIE ((uint)0x00080000) /* external interrupt enable */
+#define RCCR_SCD ((uint)0x00040000) /* scheduler configuration */
+#define RCCR_ERAM_MASK ((uint)0x0000e000) /* mask for enable RAM microcode */
+#define RCCR_ERAM_0KB ((uint)0x00000000) /* use 0KB of dpram for microcode */
+#define RCCR_ERAM_2KB ((uint)0x00002000) /* use 2KB of dpram for microcode */
+#define RCCR_ERAM_4KB ((uint)0x00004000) /* use 4KB of dpram for microcode */
+#define RCCR_ERAM_6KB ((uint)0x00006000) /* use 6KB of dpram for microcode */
+#define RCCR_ERAM_8KB ((uint)0x00008000) /* use 8KB of dpram for microcode */
+#define RCCR_ERAM_10KB ((uint)0x0000a000) /* use 10KB of dpram for microcode */
+#define RCCR_ERAM_12KB ((uint)0x0000c000) /* use 12KB of dpram for microcode */
+#define RCCR_EDM0 ((uint)0x00000800) /* DREQ0 edge detect mode */
+#define RCCR_EDM1 ((uint)0x00000400) /* DREQ1 edge detect mode */
+#define RCCR_EDM2 ((uint)0x00000200) /* DREQ2 edge detect mode */
+#define RCCR_EDM3 ((uint)0x00000100) /* DREQ3 edge detect mode */
+#define RCCR_DEM01 ((uint)0x00000008) /* DONE0/DONE1 edge detect mode */
+#define RCCR_DEM23 ((uint)0x00000004) /* DONE2/DONE3 edge detect mode */
+
+/*-----------------------------------------------------------------------
+ * CMXFCR - CMX FCC Clock Route Register
+ */
+#define CMXFCR_FC1 0x40000000 /* FCC1 connection */
+#define CMXFCR_RF1CS_MSK 0x38000000 /* Receive FCC1 Clock Source Mask */
+#define CMXFCR_TF1CS_MSK 0x07000000 /* Transmit FCC1 Clock Source Mask */
+#define CMXFCR_FC2 0x00400000 /* FCC2 connection */
+#define CMXFCR_RF2CS_MSK 0x00380000 /* Receive FCC2 Clock Source Mask */
+#define CMXFCR_TF2CS_MSK 0x00070000 /* Transmit FCC2 Clock Source Mask */
+#define CMXFCR_FC3 0x00004000 /* FCC3 connection */
+#define CMXFCR_RF3CS_MSK 0x00003800 /* Receive FCC3 Clock Source Mask */
+#define CMXFCR_TF3CS_MSK 0x00000700 /* Transmit FCC3 Clock Source Mask */
+
+#define CMXFCR_RF1CS_BRG5 0x00000000 /* Receive FCC1 Clock Source is BRG5 */
+#define CMXFCR_RF1CS_BRG6 0x08000000 /* Receive FCC1 Clock Source is BRG6 */
+#define CMXFCR_RF1CS_BRG7 0x10000000 /* Receive FCC1 Clock Source is BRG7 */
+#define CMXFCR_RF1CS_BRG8 0x18000000 /* Receive FCC1 Clock Source is BRG8 */
+#define CMXFCR_RF1CS_CLK9 0x20000000 /* Receive FCC1 Clock Source is CLK9 */
+#define CMXFCR_RF1CS_CLK10 0x28000000 /* Receive FCC1 Clock Source is CLK10 */
+#define CMXFCR_RF1CS_CLK11 0x30000000 /* Receive FCC1 Clock Source is CLK11 */
+#define CMXFCR_RF1CS_CLK12 0x38000000 /* Receive FCC1 Clock Source is CLK12 */
+
+#define CMXFCR_TF1CS_BRG5 0x00000000 /* Transmit FCC1 Clock Source is BRG5 */
+#define CMXFCR_TF1CS_BRG6 0x01000000 /* Transmit FCC1 Clock Source is BRG6 */
+#define CMXFCR_TF1CS_BRG7 0x02000000 /* Transmit FCC1 Clock Source is BRG7 */
+#define CMXFCR_TF1CS_BRG8 0x03000000 /* Transmit FCC1 Clock Source is BRG8 */
+#define CMXFCR_TF1CS_CLK9 0x04000000 /* Transmit FCC1 Clock Source is CLK9 */
+#define CMXFCR_TF1CS_CLK10 0x05000000 /* Transmit FCC1 Clock Source is CLK10 */
+#define CMXFCR_TF1CS_CLK11 0x06000000 /* Transmit FCC1 Clock Source is CLK11 */
+#define CMXFCR_TF1CS_CLK12 0x07000000 /* Transmit FCC1 Clock Source is CLK12 */
+
+#define CMXFCR_RF2CS_BRG5 0x00000000 /* Receive FCC2 Clock Source is BRG5 */
+#define CMXFCR_RF2CS_BRG6 0x00080000 /* Receive FCC2 Clock Source is BRG6 */
+#define CMXFCR_RF2CS_BRG7 0x00100000 /* Receive FCC2 Clock Source is BRG7 */
+#define CMXFCR_RF2CS_BRG8 0x00180000 /* Receive FCC2 Clock Source is BRG8 */
+#define CMXFCR_RF2CS_CLK13 0x00200000 /* Receive FCC2 Clock Source is CLK13 */
+#define CMXFCR_RF2CS_CLK14 0x00280000 /* Receive FCC2 Clock Source is CLK14 */
+#define CMXFCR_RF2CS_CLK15 0x00300000 /* Receive FCC2 Clock Source is CLK15 */
+#define CMXFCR_RF2CS_CLK16 0x00380000 /* Receive FCC2 Clock Source is CLK16 */
+
+#define CMXFCR_TF2CS_BRG5 0x00000000 /* Transmit FCC2 Clock Source is BRG5 */
+#define CMXFCR_TF2CS_BRG6 0x00010000 /* Transmit FCC2 Clock Source is BRG6 */
+#define CMXFCR_TF2CS_BRG7 0x00020000 /* Transmit FCC2 Clock Source is BRG7 */
+#define CMXFCR_TF2CS_BRG8 0x00030000 /* Transmit FCC2 Clock Source is BRG8 */
+#define CMXFCR_TF2CS_CLK13 0x00040000 /* Transmit FCC2 Clock Source is CLK13 */
+#define CMXFCR_TF2CS_CLK14 0x00050000 /* Transmit FCC2 Clock Source is CLK14 */
+#define CMXFCR_TF2CS_CLK15 0x00060000 /* Transmit FCC2 Clock Source is CLK15 */
+#define CMXFCR_TF2CS_CLK16 0x00070000 /* Transmit FCC2 Clock Source is CLK16 */
+
+#define CMXFCR_RF3CS_BRG5 0x00000000 /* Receive FCC3 Clock Source is BRG5 */
+#define CMXFCR_RF3CS_BRG6 0x00000800 /* Receive FCC3 Clock Source is BRG6 */
+#define CMXFCR_RF3CS_BRG7 0x00001000 /* Receive FCC3 Clock Source is BRG7 */
+#define CMXFCR_RF3CS_BRG8 0x00001800 /* Receive FCC3 Clock Source is BRG8 */
+#define CMXFCR_RF3CS_CLK13 0x00002000 /* Receive FCC3 Clock Source is CLK13 */
+#define CMXFCR_RF3CS_CLK14 0x00002800 /* Receive FCC3 Clock Source is CLK14 */
+#define CMXFCR_RF3CS_CLK15 0x00003000 /* Receive FCC3 Clock Source is CLK15 */
+#define CMXFCR_RF3CS_CLK16 0x00003800 /* Receive FCC3 Clock Source is CLK16 */
+
+#define CMXFCR_TF3CS_BRG5 0x00000000 /* Transmit FCC3 Clock Source is BRG5 */
+#define CMXFCR_TF3CS_BRG6 0x00000100 /* Transmit FCC3 Clock Source is BRG6 */
+#define CMXFCR_TF3CS_BRG7 0x00000200 /* Transmit FCC3 Clock Source is BRG7 */
+#define CMXFCR_TF3CS_BRG8 0x00000300 /* Transmit FCC3 Clock Source is BRG8 */
+#define CMXFCR_TF3CS_CLK13 0x00000400 /* Transmit FCC3 Clock Source is CLK13 */
+#define CMXFCR_TF3CS_CLK14 0x00000500 /* Transmit FCC3 Clock Source is CLK14 */
+#define CMXFCR_TF3CS_CLK15 0x00000600 /* Transmit FCC3 Clock Source is CLK15 */
+#define CMXFCR_TF3CS_CLK16 0x00000700 /* Transmit FCC3 Clock Source is CLK16 */
+
+/*-----------------------------------------------------------------------
+ * CMXSCR - CMX SCC Clock Route Register
+ */
+#define CMXSCR_GR1 0x80000000 /* Grant Support of SCC1 */
+#define CMXSCR_SC1 0x40000000 /* SCC1 connection */
+#define CMXSCR_RS1CS_MSK 0x38000000 /* Receive SCC1 Clock Source Mask */
+#define CMXSCR_TS1CS_MSK 0x07000000 /* Transmit SCC1 Clock Source Mask */
+#define CMXSCR_GR2 0x00800000 /* Grant Support of SCC2 */
+#define CMXSCR_SC2 0x00400000 /* SCC2 connection */
+#define CMXSCR_RS2CS_MSK 0x00380000 /* Receive SCC2 Clock Source Mask */
+#define CMXSCR_TS2CS_MSK 0x00070000 /* Transmit SCC2 Clock Source Mask */
+#define CMXSCR_GR3 0x00008000 /* Grant Support of SCC3 */
+#define CMXSCR_SC3 0x00004000 /* SCC3 connection */
+#define CMXSCR_RS3CS_MSK 0x00003800 /* Receive SCC3 Clock Source Mask */
+#define CMXSCR_TS3CS_MSK 0x00000700 /* Transmit SCC3 Clock Source Mask */
+#define CMXSCR_GR4 0x00000080 /* Grant Support of SCC4 */
+#define CMXSCR_SC4 0x00000040 /* SCC4 connection */
+#define CMXSCR_RS4CS_MSK 0x00000038 /* Receive SCC4 Clock Source Mask */
+#define CMXSCR_TS4CS_MSK 0x00000007 /* Transmit SCC4 Clock Source Mask */
+
+#define CMXSCR_RS1CS_BRG1 0x00000000 /* SCC1 Rx Clock Source is BRG1 */
+#define CMXSCR_RS1CS_BRG2 0x08000000 /* SCC1 Rx Clock Source is BRG2 */
+#define CMXSCR_RS1CS_BRG3 0x10000000 /* SCC1 Rx Clock Source is BRG3 */
+#define CMXSCR_RS1CS_BRG4 0x18000000 /* SCC1 Rx Clock Source is BRG4 */
+#define CMXSCR_RS1CS_CLK11 0x20000000 /* SCC1 Rx Clock Source is CLK11 */
+#define CMXSCR_RS1CS_CLK12 0x28000000 /* SCC1 Rx Clock Source is CLK12 */
+#define CMXSCR_RS1CS_CLK3 0x30000000 /* SCC1 Rx Clock Source is CLK3 */
+#define CMXSCR_RS1CS_CLK4 0x38000000 /* SCC1 Rx Clock Source is CLK4 */
+
+#define CMXSCR_TS1CS_BRG1 0x00000000 /* SCC1 Tx Clock Source is BRG1 */
+#define CMXSCR_TS1CS_BRG2 0x01000000 /* SCC1 Tx Clock Source is BRG2 */
+#define CMXSCR_TS1CS_BRG3 0x02000000 /* SCC1 Tx Clock Source is BRG3 */
+#define CMXSCR_TS1CS_BRG4 0x03000000 /* SCC1 Tx Clock Source is BRG4 */
+#define CMXSCR_TS1CS_CLK11 0x04000000 /* SCC1 Tx Clock Source is CLK11 */
+#define CMXSCR_TS1CS_CLK12 0x05000000 /* SCC1 Tx Clock Source is CLK12 */
+#define CMXSCR_TS1CS_CLK3 0x06000000 /* SCC1 Tx Clock Source is CLK3 */
+#define CMXSCR_TS1CS_CLK4 0x07000000 /* SCC1 Tx Clock Source is CLK4 */
+
+#define CMXSCR_RS2CS_BRG1 0x00000000 /* SCC2 Rx Clock Source is BRG1 */
+#define CMXSCR_RS2CS_BRG2 0x00080000 /* SCC2 Rx Clock Source is BRG2 */
+#define CMXSCR_RS2CS_BRG3 0x00100000 /* SCC2 Rx Clock Source is BRG3 */
+#define CMXSCR_RS2CS_BRG4 0x00180000 /* SCC2 Rx Clock Source is BRG4 */
+#define CMXSCR_RS2CS_CLK11 0x00200000 /* SCC2 Rx Clock Source is CLK11 */
+#define CMXSCR_RS2CS_CLK12 0x00280000 /* SCC2 Rx Clock Source is CLK12 */
+#define CMXSCR_RS2CS_CLK3 0x00300000 /* SCC2 Rx Clock Source is CLK3 */
+#define CMXSCR_RS2CS_CLK4 0x00380000 /* SCC2 Rx Clock Source is CLK4 */
+
+#define CMXSCR_TS2CS_BRG1 0x00000000 /* SCC2 Tx Clock Source is BRG1 */
+#define CMXSCR_TS2CS_BRG2 0x00010000 /* SCC2 Tx Clock Source is BRG2 */
+#define CMXSCR_TS2CS_BRG3 0x00020000 /* SCC2 Tx Clock Source is BRG3 */
+#define CMXSCR_TS2CS_BRG4 0x00030000 /* SCC2 Tx Clock Source is BRG4 */
+#define CMXSCR_TS2CS_CLK11 0x00040000 /* SCC2 Tx Clock Source is CLK11 */
+#define CMXSCR_TS2CS_CLK12 0x00050000 /* SCC2 Tx Clock Source is CLK12 */
+#define CMXSCR_TS2CS_CLK3 0x00060000 /* SCC2 Tx Clock Source is CLK3 */
+#define CMXSCR_TS2CS_CLK4 0x00070000 /* SCC2 Tx Clock Source is CLK4 */
+
+#define CMXSCR_RS3CS_BRG1 0x00000000 /* SCC3 Rx Clock Source is BRG1 */
+#define CMXSCR_RS3CS_BRG2 0x00000800 /* SCC3 Rx Clock Source is BRG2 */
+#define CMXSCR_RS3CS_BRG3 0x00001000 /* SCC3 Rx Clock Source is BRG3 */
+#define CMXSCR_RS3CS_BRG4 0x00001800 /* SCC3 Rx Clock Source is BRG4 */
+#define CMXSCR_RS3CS_CLK5 0x00002000 /* SCC3 Rx Clock Source is CLK5 */
+#define CMXSCR_RS3CS_CLK6 0x00002800 /* SCC3 Rx Clock Source is CLK6 */
+#define CMXSCR_RS3CS_CLK7 0x00003000 /* SCC3 Rx Clock Source is CLK7 */
+#define CMXSCR_RS3CS_CLK8 0x00003800 /* SCC3 Rx Clock Source is CLK8 */
+
+#define CMXSCR_TS3CS_BRG1 0x00000000 /* SCC3 Tx Clock Source is BRG1 */
+#define CMXSCR_TS3CS_BRG2 0x00000100 /* SCC3 Tx Clock Source is BRG2 */
+#define CMXSCR_TS3CS_BRG3 0x00000200 /* SCC3 Tx Clock Source is BRG3 */
+#define CMXSCR_TS3CS_BRG4 0x00000300 /* SCC3 Tx Clock Source is BRG4 */
+#define CMXSCR_TS3CS_CLK5 0x00000400 /* SCC3 Tx Clock Source is CLK5 */
+#define CMXSCR_TS3CS_CLK6 0x00000500 /* SCC3 Tx Clock Source is CLK6 */
+#define CMXSCR_TS3CS_CLK7 0x00000600 /* SCC3 Tx Clock Source is CLK7 */
+#define CMXSCR_TS3CS_CLK8 0x00000700 /* SCC3 Tx Clock Source is CLK8 */
+
+#define CMXSCR_RS4CS_BRG1 0x00000000 /* SCC4 Rx Clock Source is BRG1 */
+#define CMXSCR_RS4CS_BRG2 0x00000008 /* SCC4 Rx Clock Source is BRG2 */
+#define CMXSCR_RS4CS_BRG3 0x00000010 /* SCC4 Rx Clock Source is BRG3 */
+#define CMXSCR_RS4CS_BRG4 0x00000018 /* SCC4 Rx Clock Source is BRG4 */
+#define CMXSCR_RS4CS_CLK5 0x00000020 /* SCC4 Rx Clock Source is CLK5 */
+#define CMXSCR_RS4CS_CLK6 0x00000028 /* SCC4 Rx Clock Source is CLK6 */
+#define CMXSCR_RS4CS_CLK7 0x00000030 /* SCC4 Rx Clock Source is CLK7 */
+#define CMXSCR_RS4CS_CLK8 0x00000038 /* SCC4 Rx Clock Source is CLK8 */
+
+#define CMXSCR_TS4CS_BRG1 0x00000000 /* SCC4 Tx Clock Source is BRG1 */
+#define CMXSCR_TS4CS_BRG2 0x00000001 /* SCC4 Tx Clock Source is BRG2 */
+#define CMXSCR_TS4CS_BRG3 0x00000002 /* SCC4 Tx Clock Source is BRG3 */
+#define CMXSCR_TS4CS_BRG4 0x00000003 /* SCC4 Tx Clock Source is BRG4 */
+#define CMXSCR_TS4CS_CLK5 0x00000004 /* SCC4 Tx Clock Source is CLK5 */
+#define CMXSCR_TS4CS_CLK6 0x00000005 /* SCC4 Tx Clock Source is CLK6 */
+#define CMXSCR_TS4CS_CLK7 0x00000006 /* SCC4 Tx Clock Source is CLK7 */
+#define CMXSCR_TS4CS_CLK8 0x00000007 /* SCC4 Tx Clock Source is CLK8 */
+
+#endif /* __CPM2__ */
+#endif /* __KERNEL__ */
+
+
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)