patch-2.0.21-2.1.0 linux/drivers/block/xd.h
Next file: linux/drivers/cdrom/sbpcd.c
Previous file: linux/drivers/block/xd.c
Back to the patch index
Back to the overall index
- Lines: 139
- Date:
Mon Sep 30 16:52:47 1996
- Orig file:
lx2.0/v2.0.21/linux/drivers/block/xd.h
- Orig date:
Thu Jan 1 02:00:00 1970
diff -u --recursive --new-file lx2.0/v2.0.21/linux/drivers/block/xd.h linux/drivers/block/xd.h
@@ -0,0 +1,138 @@
+#ifndef _LINUX_XD_H
+#define _LINUX_XD_H
+
+/*
+ * This file contains the definitions for the IO ports and errors etc. for XT hard disk controllers (at least the DTC 5150X).
+ *
+ * Author: Pat Mackinlay, pat@it.com.au
+ * Date: 29/09/92
+ *
+ * Revised: 01/01/93, ...
+ *
+ * Ref: DTC 5150X Controller Specification (thanks to Kevin Fowler, kevinf@agora.rain.com)
+ * Also thanks to: Salvador Abreu, Dave Thaler, Risto Kankkunen and Wim Van Dorst.
+ */
+
+/* XT hard disk controller registers */
+#define XD_DATA (xd_iobase + 0x00) /* data RW register */
+#define XD_RESET (xd_iobase + 0x01) /* reset WO register */
+#define XD_STATUS (xd_iobase + 0x01) /* status RO register */
+#define XD_SELECT (xd_iobase + 0x02) /* select WO register */
+#define XD_JUMPER (xd_iobase + 0x02) /* jumper RO register */
+#define XD_CONTROL (xd_iobase + 0x03) /* DMAE/INTE WO register */
+#define XD_RESERVED (xd_iobase + 0x03) /* reserved */
+
+/* XT hard disk controller commands (incomplete list) */
+#define CMD_TESTREADY 0x00 /* test drive ready */
+#define CMD_RECALIBRATE 0x01 /* recalibrate drive */
+#define CMD_SENSE 0x03 /* request sense */
+#define CMD_FORMATDRV 0x04 /* format drive */
+#define CMD_VERIFY 0x05 /* read verify */
+#define CMD_FORMATTRK 0x06 /* format track */
+#define CMD_FORMATBAD 0x07 /* format bad track */
+#define CMD_READ 0x08 /* read */
+#define CMD_WRITE 0x0A /* write */
+#define CMD_SEEK 0x0B /* seek */
+
+/* Controller specific commands */
+#define CMD_DTCSETPARAM 0x0C /* set drive parameters (DTC 5150X only?) */
+#define CMD_DTCGETECC 0x0D /* get ecc error length (DTC 5150X only?) */
+#define CMD_DTCREADBUF 0x0E /* read sector buffer (DTC 5150X only?) */
+#define CMD_DTCWRITEBUF 0x0F /* write sector buffer (DTC 5150X only?) */
+#define CMD_DTCREMAPTRK 0x11 /* assign alternate track (DTC 5150X only?) */
+#define CMD_DTCGETPARAM 0xFB /* get drive parameters (DTC 5150X only?) */
+#define CMD_DTCSETSTEP 0xFC /* set step rate (DTC 5150X only?) */
+#define CMD_DTCSETGEOM 0xFE /* set geometry data (DTC 5150X only?) */
+#define CMD_DTCGETGEOM 0xFF /* get geometry data (DTC 5150X only?) */
+#define CMD_ST11GETGEOM 0xF8 /* get geometry data (Seagate ST11R/M only?) */
+#define CMD_WDSETPARAM 0x0C /* set drive parameters (WD 1004A27X only?) */
+
+/* Bits for command status byte */
+#define CSB_ERROR 0x02 /* error */
+#define CSB_LUN 0x20 /* logical Unit Number */
+
+/* XT hard disk controller status bits */
+#define STAT_READY 0x01 /* controller is ready */
+#define STAT_INPUT 0x02 /* data flowing from controller to host */
+#define STAT_COMMAND 0x04 /* controller in command phase */
+#define STAT_SELECT 0x08 /* controller is selected */
+#define STAT_REQUEST 0x10 /* controller requesting data */
+#define STAT_INTERRUPT 0x20 /* controller requesting interrupt */
+
+/* XT hard disk controller control bits */
+#define PIO_MODE 0x00 /* control bits to set for PIO */
+#define DMA_MODE 0x03 /* control bits to set for DMA & interrupt */
+
+#define XD_MAXDRIVES 2 /* maximum 2 drives */
+#define XD_TIMEOUT HZ /* 1 second timeout */
+#define XD_RETRIES 4 /* maximum 4 retries */
+
+#undef DEBUG /* define for debugging output */
+
+#ifdef DEBUG
+ #define DEBUG_STARTUP /* debug driver initialisation */
+ #define DEBUG_OVERRIDE /* debug override geometry detection */
+ #define DEBUG_READWRITE /* debug each read/write command */
+ #define DEBUG_OTHER /* debug misc. interrupt/DMA stuff */
+ #define DEBUG_COMMAND /* debug each controller command */
+#endif /* DEBUG */
+
+/* this structure defines the XT drives and their types */
+typedef struct {
+ u_char heads;
+ u_short cylinders;
+ u_char sectors;
+ u_char control;
+} XD_INFO;
+
+#define HDIO_GETGEO 0x0301 /* get drive geometry */
+
+/* this structure is returned to the HDIO_GETGEO ioctl */
+typedef struct {
+ __u8 heads;
+ __u8 sectors;
+ __u8 cylinders;
+ __u32 start;
+} XD_GEOMETRY;
+
+/* this structure defines a ROM BIOS signature */
+typedef struct {
+ unsigned int offset;
+ const char *string;
+ void (*init_controller)(unsigned int address);
+ void (*init_drive)(u_char drive);
+ const char *name;
+} XD_SIGNATURE;
+
+void xd_setup (char *command,int *integers);
+static u_char xd_detect (u_char *controller, unsigned int *address);
+static u_char xd_initdrives (void (*init_drive)(u_char drive));
+static void xd_geninit (struct gendisk *);
+
+static int xd_open (struct inode *inode,struct file *file);
+static void do_xd_request (void);
+static int xd_ioctl (struct inode *inode,struct file *file,unsigned int cmd,unsigned long arg);
+static void xd_release (struct inode *inode,struct file *file);
+static int xd_reread_partitions (kdev_t dev);
+static int xd_readwrite (u_char operation,u_char drive,char *buffer,u_int block,u_int count);
+static void xd_recalibrate (u_char drive);
+
+static void xd_interrupt_handler (int irq, void *dev_id, struct pt_regs *regs);
+static u_char xd_setup_dma (u_char opcode,u_char *buffer,u_int count);
+static u_char *xd_build (u_char *cmdblk,u_char command,u_char drive,u_char head,u_short cylinder,u_char sector,u_char count,u_char control);
+static inline u_char xd_waitport (u_short port,u_char flags,u_char mask,u_long timeout);
+static u_int xd_command (u_char *command,u_char mode,u_char *indata,u_char *outdata,u_char *sense,u_long timeout);
+
+/* card specific setup and geometry gathering code */
+static void xd_dtc_init_controller (unsigned int address);
+static void xd_dtc_init_drive (u_char drive);
+static void xd_wd_init_controller (unsigned int address);
+static void xd_wd_init_drive (u_char drive);
+static void xd_seagate_init_controller (unsigned int address);
+static void xd_seagate_init_drive (u_char drive);
+static void xd_omti_init_controller (unsigned int address);
+static void xd_omti_init_drive (u_char drive);
+static void xd_setparam (u_char command,u_char drive,u_char heads,u_short cylinders,u_short rwrite,u_short wprecomp,u_char ecc);
+static void xd_override_init_drive (u_char drive);
+
+#endif /* _LINUX_XD_H */
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen, slshen@lbl.gov