patch-2.1.70 linux/include/linux/cm206.h

• Lines: 178
• Date: Wed Dec 31 16:00:00 1969
• Orig file: v2.1.69/linux/include/linux/cm206.h
• Orig date: Wed May 15 00:06:26 1996

diff -u --recursive --new-file v2.1.69/linux/include/linux/cm206.h linux/include/linux/cm206.h
@@ -1,177 +0,0 @@
-/* cm206.h Header file for cm206.c.
-   Copyright (c) 1995 David van Leeuwen 
-*/
-
-#ifndef LINUX_CM206_H
-#define LINUX_CM206_H
-
-#include <linux/ioctl.h>
-
-/* First, the cm260 stuff */
-/* The ports and irq used. Although CM206_BASE and CM206_IRQ are defined
-   below, the values are not used unless autoprobing is turned off and 
-   no LILO boot options or module command line options are given. Change
-   these values to your own as last resort if autoprobing and options
-   don't work. */
-
-#define CM206_BASE 0x340
-#define CM206_IRQ 11
-
-#define r_data_status (cm206_base)
-#define r_uart_receive (cm206_base+0x2)
-#define r_fifo_output_buffer (cm206_base+0x4)
-#define r_line_status (cm206_base+0x6)
-#define r_data_control (cm206_base+0x8)
-#define r_uart_transmit (cm206_base+0xa)
-#define r_test_clock (cm206_base+0xc)
-#define r_test_control (cm206_base+0xe)
-
-/* the data_status flags */
-#define ds_ram_size 0x4000
-#define ds_toc_ready 0x2000
-#define ds_fifo_empty 0x1000
-#define ds_sync_error 0x800
-#define ds_crc_error 0x400
-#define ds_data_error 0x200
-#define ds_fifo_overflow 0x100
-#define ds_data_ready 0x80
-
-/* the line_status flags */
-#define ls_attention 0x10
-#define ls_parity_error 0x8
-#define ls_overrun 0x4
-#define ls_receive_buffer_full 0x2
-#define ls_transmitter_buffer_empty 0x1
-
-/* the data control register flags */
-#define dc_read_q_channel 0x4000
-#define dc_mask_sync_error 0x2000
-#define dc_toc_enable 0x1000
-#define dc_no_stop_on_error 0x800
-#define dc_break 0x400
-#define dc_initialize 0x200
-#define dc_mask_transmit_ready 0x100
-#define dc_flag_enable 0x80
-
-/* Define the default data control register flags here */
-#define dc_normal (dc_mask_sync_error | dc_no_stop_on_error | \
-		   dc_mask_transmit_ready)
-
-/* now some constants related to the cm206 */
-/* another drive status byte, echoed by the cm206 on most commands */
-
-#define dsb_error_condition 0x1
-#define dsb_play_in_progress 0x4
-#define dsb_possible_media_change 0x8
-#define dsb_disc_present 0x10
-#define dsb_drive_not_ready 0x20
-#define dsb_tray_locked 0x40
-#define dsb_tray_not_closed 0x80
-
-#define dsb_not_useful (dsb_drive_not_ready | dsb_tray_not_closed)
-
-/* the cm206 command set */
-
-#define c_close_tray 0
-#define c_lock_tray 0x01
-#define c_unlock_tray 0x04
-#define c_open_tray 0x05
-#define c_seek 0x10
-#define c_read_data 0x20
-#define c_force_1x 0x21
-#define c_force_2x 0x22
-#define c_auto_mode 0x23
-#define c_play 0x30
-#define c_set_audio_mode 0x31
-#define c_read_current_q 0x41
-#define c_stream_q 0x42
-#define c_drive_status 0x50
-#define c_disc_status 0x51
-#define c_audio_status 0x52
-#define c_drive_configuration 0x53
-#define c_read_upc 0x60
-#define c_stop 0x70
-#define c_calc_checksum 0xe5
-
-#define c_gimme 0xf8
-
-/* finally, the (error) condition that the drive can be in      *
- * OK, this is not always an error, but let's prefix it with e_ */
-
-#define e_none 0
-#define e_illegal_command 0x01
-#define e_sync 0x02
-#define e_seek 0x03
-#define e_parity 0x04
-#define e_focus 0x05
-#define e_header_sync 0x06
-#define e_code_incompatibility 0x07
-#define e_reset_done 0x08
-#define e_bad_parameter 0x09
-#define e_radial 0x0a
-#define e_sub_code 0x0b
-#define e_no_data_track 0x0c
-#define e_scan 0x0d
-#define e_tray_open 0x0f
-#define e_no_disc 0x10
-#define e_tray stalled 0x11
-
-/* drive configuration masks */
-
-#define dcf_revision_code 0x7
-#define dcf_transfer_rate 0x60
-#define dcf_motorized_tray 0x80
-
-/* disc status byte */
-
-#define cds_multi_session 0x2
-#define cds_all_audio 0x8
-#define cds_xa_mode 0xf0
-
-/* finally some ioctls for the driver */
-
-#define CM206CTL_GET_STAT _IO( 0x20, 0 )
-#define CM206CTL_GET_LAST_STAT _IO( 0x20, 1 )
-
-/* for kernel 1.2.n */
-#if !defined(CDROM_GET_UPC)
-#define CDROM_GET_UPC _IO( 'S', 0x11 )
-#define CDROMRESET _IO( 'S', 0x12 )
-#endif
-
-#ifdef STATISTICS
-
-/* This is an ugly way to guarantee that the names of the statistics
- * are the same in the code and in the diagnostics program.  */
-
-#ifdef __KERNEL__
-#define x(a) st_ ## a
-#define y enum
-#else
-#define x(a) #a
-#define y char * stats_name[] = 
-#endif
-
-y {x(interrupt), x(data_ready), x(fifo_overflow), x(data_error),
-     x(crc_error), x(sync_error), x(lost_intr), x(echo),
-     x(write_timeout), x(receive_timeout), x(read_timeout),
-     x(dsb_timeout), x(stop_0xff), x(back_read_timeout),
-     x(sector_transferred), x(read_restarted), x(read_background),
-     x(bh), x(open), x(ioctl_multisession), x(attention)
-#ifdef __KERNEL__
-     , x(last_entry)
-#endif
- };
-
-#ifdef __KERNEL__
-#define NR_STATS st_last_entry
-#else
-#define NR_STATS (sizeof(stats_name)/sizeof(char*))
-#endif
-
-#undef y
-#undef x
-
-#endif STATISTICS
-
-#endif LINUX_CM206_H