patch-2.1.87 linux/drivers/sound/Config.in

Next file: linux/drivers/sound/Makefile
Previous file: linux/drivers/scsi/sr.c
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.1.86/linux/drivers/sound/Config.in linux/drivers/sound/Config.in
@@ -1,19 +1,19 @@
 dep_tristate 'ProAudioSpectrum 16 support' CONFIG_PAS $CONFIG_SOUND
 if [ "$CONFIG_PAS" = "y" ]; then
-    int 'PAS16 IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14 or 15' PAS_IRQ 10
-    int 'PAS16 DMA 0, 1, 3, 5, 6 or 7' PAS_DMA 3
+    int 'PAS16 IRQ 3, 4, 5, 7, 9, 10, 11, 12, 14 or 15' CONFIG_PAS_IRQ 10
+    int 'PAS16 DMA 0, 1, 3, 5, 6 or 7' CONFIG_PAS_DMA 3
 fi
 
 dep_tristate '100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support' CONFIG_SB $CONFIG_SOUND
 if [ "$CONFIG_SB" = "y" ]; then
-    hex 'I/O base for SB Check from manual of the card' SBC_BASE 220
-    int 'Sound Blaster IRQ Check from manual of the card' SBC_IRQ 7
-    int 'Sound Blaster DMA 0, 1 or 3' SBC_DMA 1
-    int 'Sound Blaster 16 bit DMA (SB16, Jazz16, SMW) 5, 6 or 7 (use 1 for 8 bit cards)' SB_DMA2 5
-    hex 'MPU401 I/O base of SB16, Jazz16 and ES1688 Check from manual of the card' SB_MPU_BASE 330
+    hex 'I/O base for SB Check from manual of the card' CONFIG_SB_BASE 220
+    int 'Sound Blaster IRQ Check from manual of the card' CONFIG_SB_IRQ 7
+    int 'Sound Blaster DMA 0, 1 or 3' CONFIG_SB_DMA 1
+    int 'Sound Blaster 16 bit DMA (SB16, Jazz16, SMW) 5, 6 or 7 (use 1 for 8 bit cards)' CONFIG_SB_DMA2 5
+    hex 'MPU401 I/O base of SB16, Jazz16 and ES1688 Check from manual of the card' CONFIG_SB_MPU_BASE 330
     comment 'MPU401 IRQ is only required with Jazz16, SM Wave and ESS1688.'
     comment 'Enter -1 to the following question if you have something else such as SB16/32.'
-    int 'SB MPU401 IRQ (Jazz16, SM Wave and ES1688) Check from manual of the card' SB_MPU_IRQ -1
+    int 'SB MPU401 IRQ (Jazz16, SM Wave and ES1688) Check from manual of the card' CONFIG_SB_MPU_IRQ -1
 fi
 
 dep_tristate 'Generic OPL2/OPL3 FM synthesizer support' CONFIG_ADLIB $CONFIG_SOUND
@@ -23,116 +23,116 @@
     bool '16 bit sampling option of GUS (_NOT_ GUS MAX)' CONFIG_GUS16 
     bool 'GUS MAX support' CONFIG_GUSMAX
     if [ "$CONFIG_GUS" = "y" ]; then
-	hex 'I/O base for GUS 210, 220, 230, 240, 250 or 260' GUS_BASE 220
-	int 'GUS IRQ 3, 5, 7, 9, 11, 12 or 15' GUS_IRQ 15
-	int 'GUS DMA 1, 3, 5, 6 or 7' GUS_DMA 6
-	int 'Second DMA channel for GUS 1, 3, 5, 6 or 7' GUS_DMA2 -1
+	hex 'I/O base for GUS 210, 220, 230, 240, 250 or 260' CONFIG_GUS_BASE 220
+	int 'GUS IRQ 3, 5, 7, 9, 11, 12 or 15' CONFIG_GUS_IRQ 15
+	int 'GUS DMA 1, 3, 5, 6 or 7' CONFIG_GUS_DMA 6
+	int 'Second DMA channel for GUS 1, 3, 5, 6 or 7' CONFIG_GUS_DMA2 -1
 	if [ "$CONFIG_GUS16" = "y" ]; then
-	    hex 'I/O base for the 16 bit daughtercard of GUS 530, 604, E80 or F40' GUS16_BASE 530
-	    int 'GUS 16 bit daughtercard IRQ 3, 4, 5, 7, or 9' GUS16_IRQ 7
-	    int 'GUS DMA 0, 1 or 3' GUS16_DMA 3
+	    hex 'I/O base for the 16 bit daughtercard of GUS 530, 604, E80 or F40' CONFIG_GUS16_BASE 530
+	    int 'GUS 16 bit daughtercard IRQ 3, 4, 5, 7, or 9' CONFIG_GUS16_IRQ 7
+	    int 'GUS DMA 0, 1 or 3' CONFIG_GUS16_DMA 3
 	fi
     fi
 fi
 
 dep_tristate 'MPU-401 support (NOT for SB16)' CONFIG_MPU401 $CONFIG_SOUND
 if [ "$CONFIG_MPU401" = "y" ]; then
-    hex 'I/O base for MPU401 Check from manual of the card' MPU_BASE 330
-    int 'MPU401 IRQ Check from manual of the card' MPU_IRQ 9
+    hex 'I/O base for MPU401 Check from manual of the card' CONFIG_MPU_BASE 330
+    int 'MPU401 IRQ Check from manual of the card' CONFIG_MPU_IRQ 9
 fi
 
 dep_tristate 'PSS (ECHO-ADI2111) support' CONFIG_PSS $CONFIG_SOUND
 if [ "$CONFIG_PSS" = "y" ]; then
-    hex 'PSS I/O base 220 or 240' PSS_BASE 220
-    hex 'PSS audio I/O base 530, 604, E80 or F40' PSS_MSS_BASE 530
-    int 'PSS audio IRQ 7, 9, 10 or 11' PSS_MSS_IRQ 11
-    int 'PSS audio DMA 0, 1 or 3' PSS_MSS_DMA 3
-    hex 'PSS MIDI I/O base ' PSS_MPU_BASE 330
-    int 'PSS MIDI IRQ 3, 4, 5, 7 or 9' PSS_MPU_IRQ 9
-    bool '  Have DSPxxx.LD firmware file' PSS_HAVE_BOOT
-    if [ "$PSS_HAVE_BOOT" = "y" ]; then
-       string '  Full pathname of DSPxxx.LD firmware file' PSS_BOOT_FILE
+    hex 'PSS I/O base 220 or 240' CONFIG_PSS_BASE 220
+    hex 'PSS audio I/O base 530, 604, E80 or F40' CONFIG_PSS_MSS_BASE 530
+    int 'PSS audio IRQ 7, 9, 10 or 11' CONFIG_PSS_MSS_IRQ 11
+    int 'PSS audio DMA 0, 1 or 3' CONFIG_PSS_MSS_DMA 3
+    hex 'PSS MIDI I/O base ' CONFIG_PSS_MPU_BASE 330
+    int 'PSS MIDI IRQ 3, 4, 5, 7 or 9' CONFIG_PSS_MPU_IRQ 9
+    bool '  Have DSPxxx.LD firmware file' CONFIG_PSS_HAVE_BOOT
+    if [ "$CONFIG_PSS_HAVE_BOOT" = "y" ]; then
+       string '  Full pathname of DSPxxx.LD firmware file' CONFIG_PSS_BOOT_FILE
     fi
 fi
 
 dep_tristate 'Microsoft Sound System support' CONFIG_MSS $CONFIG_SOUND
 if [ "$CONFIG_MSS" = "y" ]; then
-    hex 'MSS/WSS I/O base 530, 604, E80 or F40' MSS_BASE 530
-    int 'MSS/WSS IRQ 7, 9, 10 or 11' MSS_IRQ 11
-    int 'MSS/WSS DMA 0, 1 or 3' MSS_DMA 3
-    int 'MSS/WSS second DMA (if possible) 0, 1 or 3' MSS_DMA2 -1
+    hex 'MSS/WSS I/O base 530, 604, E80 or F40' CONFIG_MSS_BASE 530
+    int 'MSS/WSS IRQ 7, 9, 10 or 11' CONFIG_MSS_IRQ 11
+    int 'MSS/WSS DMA 0, 1 or 3' CONFIG_MSS_DMA 3
+    int 'MSS/WSS second DMA (if possible) 0, 1 or 3' CONFIG_MSS_DMA2 -1
 fi
 
 dep_tristate 'Ensoniq SoundScape support' CONFIG_SSCAPE $CONFIG_SOUND
 if [ "$CONFIG_SSCAPE" = "y" ]; then
-    hex 'SoundScape MIDI I/O base 320, 330, 340 or 350' SSCAPE_BASE 330
-    int 'SoundScape MIDI IRQ ' SSCAPE_IRQ 9
-    int 'SoundScape initialization DMA 0, 1 or 3' SSCAPE_DMA 3
-    hex 'SoundScape audio I/O base 534, 608, E84 or F44' SSCAPE_MSS_BASE 534
-    int 'SoundScape audio IRQ 7, 9, 10 or 11' SSCAPE_MSS_IRQ 11
+    hex 'SoundScape MIDI I/O base 320, 330, 340 or 350' CONFIG_SSCAPE_BASE 330
+    int 'SoundScape MIDI IRQ ' CONFIG_SSCAPE_IRQ 9
+    int 'SoundScape initialization DMA 0, 1 or 3' CONFIG_SSCAPE_DMA 3
+    hex 'SoundScape audio I/O base 534, 608, E84 or F44' CONFIG_SSCAPE_MSS_BASE 534
+    int 'SoundScape audio IRQ 7, 9, 10 or 11' CONFIG_SSCAPE_MSS_IRQ 11
 fi
 
 dep_tristate 'MediaTrix AudioTrix Pro support' CONFIG_TRIX $CONFIG_SOUND
 if [ "$CONFIG_TRIX" = "y" ]; then
-    hex 'OPL3-SA1 audio I/O base 530, 604, E80 or F40' TRIX_BASE 530
-    int 'OPL3-SA1 audio IRQ 7, 9, 10 or 11' TRIX_IRQ 11
-    int 'OPL3-SA1 audio DMA 0, 1 or 3' TRIX_DMA 0
-    int 'OPL3-SA1 second (duplex) DMA 0, 1 or 3' TRIX_DMA2 3
-    hex 'OPL3-SA1 MIDI I/O base 330, 370, 3B0 or 3F0' TRIX_MPU_BASE 330
-    int 'OPL3-SA1 MIDI IRQ 3, 4, 5, 7 or 9' TRIX_MPU_IRQ 9
-    hex 'OPL3-SA1 SB I/O base 220, 210, 230, 240, 250, 260 or 270' TRIX_SB_BASE 220
-    int 'OPL3-SA1 SB IRQ 3, 4, 5 or 7' TRIX_SB_IRQ 7
-    int 'OPL3-SA1 SB DMA 1 or 3' TRIX_SB_DMA 1
-    bool '  Have TRXPRO.HEX firmware file' TRIX_HAVE_BOOT
-    if [ "$TRIX_HAVE_BOOT" = "y" ]; then
-	string '  Full pathname of TRXPRO.HEX firmware file' TRIX_BOOT_FILE
+    hex 'OPL3-SA1 audio I/O base 530, 604, E80 or F40' CONFIG_TRIX_BASE 530
+    int 'OPL3-SA1 audio IRQ 7, 9, 10 or 11' CONFIG_TRIX_IRQ 11
+    int 'OPL3-SA1 audio DMA 0, 1 or 3' CONFIG_TRIX_DMA 0
+    int 'OPL3-SA1 second (duplex) DMA 0, 1 or 3' CONFIG_TRIX_DMA2 3
+    hex 'OPL3-SA1 MIDI I/O base 330, 370, 3B0 or 3F0' CONFIG_TRIX_MPU_BASE 330
+    int 'OPL3-SA1 MIDI IRQ 3, 4, 5, 7 or 9' CONFIG_TRIX_MPU_IRQ 9
+    hex 'OPL3-SA1 SB I/O base 220, 210, 230, 240, 250, 260 or 270' CONFIG_TRIX_SB_BASE 220
+    int 'OPL3-SA1 SB IRQ 3, 4, 5 or 7' CONFIG_TRIX_SB_IRQ 7
+    int 'OPL3-SA1 SB DMA 1 or 3' CONFIG_TRIX_SB_DMA 1
+    bool '  Have TRXPRO.HEX firmware file' CONFIG_TRIX_HAVE_BOOT
+    if [ "$CONFIG_TRIX_HAVE_BOOT" = "y" ]; then
+	string '  Full pathname of TRXPRO.HEX firmware file' CONFIG_TRIX_BOOT_FILE
     fi
 fi
 
 dep_tristate 'Support for OPTi MAD16 and/or Mozart based cards' CONFIG_MAD16 $CONFIG_SOUND
 if [ "$CONFIG_MAD16" = "y" ]; then
-    hex 'MAD16 audio I/O base 530, 604, E80 or F40' MAD16_BASE 530
-    int 'MAD16 audio IRQ 7, 9, 10 or 11' MAD16_IRQ 11
-    int 'MAD16 audio DMA 0, 1 or 3' MAD16_DMA 3
-    int 'MAD16 second (duplex) DMA 0, 1 or 3' MAD16_DMA2 0
-    hex 'MAD16 MIDI I/O base 300, 310, 320 or 330 (0 disables)' MAD16_MPU_BASE 330
-    int 'MAD16 MIDI IRQ 5, 7, 9 or 10' MAD16_MPU_IRQ 9
+    hex 'MAD16 audio I/O base 530, 604, E80 or F40' CONFIG_MAD16_BASE 530
+    int 'MAD16 audio IRQ 7, 9, 10 or 11' CONFIG_MAD16_IRQ 11
+    int 'MAD16 audio DMA 0, 1 or 3' CONFIG_MAD16_DMA 3
+    int 'MAD16 second (duplex) DMA 0, 1 or 3' CONFIG_MAD16_DMA2 0
+    hex 'MAD16 MIDI I/O base 300, 310, 320 or 330 (0 disables)' CONFIG_MAD16_MPU_BASE 330
+    int 'MAD16 MIDI IRQ 5, 7, 9 or 10' CONFIG_MAD16_MPU_IRQ 9
 fi
 
 dep_tristate 'Support for Crystal CS4232 based (PnP) cards' CONFIG_CS4232 $CONFIG_SOUND
 if [ "$CONFIG_CS4232" = "y" ]; then
-    hex 'CS4232 audio I/O base 530, 604, E80 or F40' CS4232_BASE 530
-    int 'CS4232 audio IRQ 5, 7, 9, 11, 12 or 15' CS4232_IRQ 11
-    int 'CS4232 audio DMA 0, 1 or 3' CS4232_DMA 0
-    int 'CS4232 second (duplex) DMA 0, 1 or 3' CS4232_DMA2 3
-    hex 'CS4232 MIDI I/O base 330, 370, 3B0 or 3F0' CS4232_MPU_BASE 330
-    int 'CS4232 MIDI IRQ 5, 7, 9, 11, 12 or 15' CS4232_MPU_IRQ 9
+    hex 'CS4232 audio I/O base 530, 604, E80 or F40' CONFIG_CS4232_BASE 530
+    int 'CS4232 audio IRQ 5, 7, 9, 11, 12 or 15' CONFIG_CS4232_IRQ 11
+    int 'CS4232 audio DMA 0, 1 or 3' CONFIG_CS4232_DMA 0
+    int 'CS4232 second (duplex) DMA 0, 1 or 3' CONFIG_CS4232_DMA2 3
+    hex 'CS4232 MIDI I/O base 330, 370, 3B0 or 3F0' CONFIG_CS4232_MPU_BASE 330
+    int 'CS4232 MIDI IRQ 5, 7, 9, 11, 12 or 15' CONFIG_CS4232_MPU_IRQ 9
 fi
 
 dep_tristate 'Support for Turtle Beach Wave Front (Maui, Tropez) synthesizers' CONFIG_MAUI $CONFIG_SOUND
 if [ "$CONFIG_MAUI" = "y" ]; then
-    hex 'I/O base for Maui 210, 230, 260, 290, 300, 320, 338 or 330' MAUI_BASE 330
-    int 'Maui IRQ 5, 9, 12 or 15' MAUI_IRQ 9
-    bool '  Have OSWF.MOT firmware file' MAUI_HAVE_BOOT
-    if [ "$MAUI_HAVE_BOOT" = "y" ]; then
-	string '  Full pathname of OSWF.MOT firmware file' MAUI_BOOT_FILE
+    hex 'I/O base for Maui 210, 230, 260, 290, 300, 320, 338 or 330' CONFIG_MAUI_BASE 330
+    int 'Maui IRQ 5, 9, 12 or 15' CONFIG_MAUI_IRQ 9
+    bool '  Have OSWF.MOT firmware file' CONFIG_MAUI_HAVE_BOOT
+    if [ "$CONFIG_MAUI_HAVE_BOOT" = "y" ]; then
+	string '  Full pathname of OSWF.MOT firmware file' CONFIG_MAUI_BOOT_FILE
     fi
 fi
 
 dep_tristate 'Yamaha OPL3-SA1 audio controller' CONFIG_OPL3SA1 $CONFIG_SOUND
 if [ "$CONFIG_OPL3SA1" = "y" ]; then
-    hex 'OPL3-SA1 audio I/O base 530, 604, E80 or F40' OPL3SA1_BASE 530
-    int 'OPL3-SA1 audio IRQ 7, 9, 10 or 11' OPL3SA1_IRQ 11
-    int 'OPL3-SA1 audio DMA 0, 1 or 3' OPL3SA1_DMA 0
-    int 'OPL3-SA1 second (duplex) DMA 0, 1 or 3' OPL3SA1_DMA2 3
-    hex 'OPL3-SA1 MIDI I/O base 330, 370, 3B0 or 3F0' OPL3SA1_MPU_BASE 330
-    int 'OPL3-SA1 MIDI IRQ 3, 4, 5, 7 or 9' OPL3SA1_MPU_IRQ 9
+    hex 'OPL3-SA1 audio I/O base 530, 604, E80 or F40' CONFIG_OPL3SA1_BASE 530
+    int 'OPL3-SA1 audio IRQ 7, 9, 10 or 11' CONFIG_OPL3SA1_IRQ 11
+    int 'OPL3-SA1 audio DMA 0, 1 or 3' CONFIG_OPL3SA1_DMA 0
+    int 'OPL3-SA1 second (duplex) DMA 0, 1 or 3' CONFIG_OPL3SA1_DMA2 3
+    hex 'OPL3-SA1 MIDI I/O base 330, 370, 3B0 or 3F0' CONFIG_OPL3SA1_MPU_BASE 330
+    int 'OPL3-SA1 MIDI IRQ 3, 4, 5, 7 or 9' CONFIG_OPL3SA1_MPU_IRQ 9
 fi
 
 dep_tristate 'SoftOSS software wave table engine' CONFIG_SOFTOSS $CONFIG_SOUND
 if [ "$CONFIG_SOFTOSS" = "y" ]; then
-    int 'Sampling rate for SoftOSS 8000 to 48000' SOFTOSS_RATE 22050
-    int 'Max # of concurrent voices for SoftOSS 4 to 32' SOFTOSS_VOICES 32
+    int 'Sampling rate for SoftOSS 8000 to 48000' CONFIG_SOFTOSS_RATE 22050
+    int 'Max # of concurrent voices for SoftOSS 4 to 32' CONFIG_SOFTOSS_VOICES 32
 fi
 
 dep_tristate 'FM synthesizer (YM3812/OPL-3) support' CONFIG_YM3812 $CONFIG_SOUND
@@ -140,8 +140,8 @@
 
 dep_tristate '6850 UART support' CONFIG_UART6850 $CONFIG_SOUND
 if [ "$CONFIG_UART6850" = "y" ]; then
-    hex 'I/O base for UART 6850 MIDI port (Unknown)' U6850_BASE 0
-    int 'UART6850 IRQ (Unknown)' U6850_IRQ -1
+    hex 'I/O base for UART 6850 MIDI port (Unknown)' CONFIG_U6850_BASE 0
+    int 'UART6850 IRQ (Unknown)' CONFIG_U6850_IRQ -1
 fi
 
 
@@ -153,7 +153,7 @@
    dep_tristate 'Gallant Audio Cards (SC-6000 and SC-6600 based)' CONFIG_AEDSP16 $CONFIG_SOUND
 
    if [ "$CONFIG_AEDSP16" = "y" -o "$CONFIG_AEDSP16" = "m" ]; then
-      hex '  I/O base for Audio Excel DSP 16 220 or 240' AEDSP16_BASE 220
+      hex '  I/O base for Audio Excel DSP 16 220 or 240' CONFIG_AEDSP16_BASE 220
    fi
 
    if [ "$CONFIG_AEDSP16" = "y" ]; then
@@ -165,10 +165,10 @@
          if [ "$CONFIG_AEDSP16_SBPRO" = "y" ]; then
 	    comment 'Audio Excel DSP 16 [Sound Blaster Pro]'
             hex 'I/O base for Audio Excel DSP 16 220 or 240' \
-	                                           AEDSP16_BASE $SBC_BASE
+	                                           CONFIG_AEDSP16_BASE $CONFIG_SB_BASE
             int 'Audio Excel DSP 16 IRQ 5, 7, 9, 10, 11' \
-	                                           AEDSP16_SBC_IRQ $SBC_IRQ
-            int 'Audio Excel DSP 16 DMA 0, 1 or 3' AEDSP16_SBC_DMA $SBC_DMA
+	                                           CONFIG_AEDSP16_SB_IRQ $CONFIG_SB_IRQ
+            int 'Audio Excel DSP 16 DMA 0, 1 or 3' CONFIG_AEDSP16_SB_DMA $CONFIG_SB_DMA
          fi
       fi
    
@@ -176,10 +176,10 @@
          bool 'Audio Excel DSP 16 (MSS emulation)' CONFIG_AEDSP16_MSS
          if [ "$CONFIG_AEDSP16_MSS" = "y" ]; then
 	    comment 'Audio Excel DSP 16 [Microsoft Sound System]'
-	    hex 'I/O base for Audio Excel DSP 16 220 or 240' AEDSP16_BASE 220
+	    hex 'I/O base for Audio Excel DSP 16 220 or 240' CONFIG_AEDSP16_BASE 220
             int 'Audio Excel DSP 16 IRQ 5, 7, 9, 10, 11' \
-	                                           AEDSP16_MSS_IRQ $MSS_IRQ
-            int 'Audio Excel DSP 16 DMA 0, 1 or 3' AEDSP16_MSS_DMA $MSS_DMA
+	                                           CONFIG_AEDSP16_MSS_IRQ $CONFIG_MSS_IRQ
+            int 'Audio Excel DSP 16 DMA 0, 1 or 3' CONFIG_AEDSP16_MSS_DMA $CONFIG_MSS_DMA
          fi
       fi
 
@@ -189,10 +189,10 @@
 	    comment 'Audio Excel DSP 16 [MPU-401]'
 	    if [ "$CONFIG_AEDSP16_SBPRO" != "y" \
 	         -a "$CONFIG_AEDSP16_MSS" != "y" ]; then
-	       hex 'I/O base for Audio Excel DSP 16 220 or 240' AEDSP16_BASE 220
+	       hex 'I/O base for Audio Excel DSP 16 220 or 240' CONFIG_AEDSP16_BASE 220
 	    fi
             int 'MPU401 IRQ for Audio Excel DSP 16 5, 7, 9, 10 or 0 (disable)' \
-	    						AEDSP16_MPU_IRQ $MPU_IRQ
+	    						CONFIG_AEDSP16_MPU_IRQ $CONFIG_MPU_IRQ
          fi
       fi
    fi

FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen, slshen@lbl.gov